hypercube 3d models

Hello dear community Actually i'm building the Hypercube 3D printer from Tech2C http://www.thingiverse.com/thing:1752766 and the part list has some items with a very long shipping time... To keep the build time as short as possible i've designed my...

UPDATE see: Improved Anti Backlash Nut in OpenSCAD This anti backlash nut is based on nuts I bought for the HyperCube Evolution, found in a custom bracket I created at https://www.thingiverse.com/thing:2630802. Note that an updated and improved...

Reduced winter entrance for an "austrian Einheitsmaß" beehive. Printed in two parts with puzzle connection (tight fit). Use ASA for UV resistance outside. Length = 400 mm Width = 50 mm Thickness = 3,2 mm Print Settings Printer: Hypercube Evolution...

This is probably only going to help a handful of people who bought a Svive Hydra Elite mic so i've attached the .step files if anyone want to edit this thing. As of right now there is no shockmount availible for the above mentioned mic so i made...

This custom enclosure has been engineered to accommodate an Ultratronics board within a sturdy corexy frame constructed from robust 20x20 profiles, just like my own Hypercube setup.\r\n\r\nConvenient openings are strategically placed on the enclosure...

This is my custom mount for a MKS SKR 1.3 Board on my Hypercube Evolution. It can also hold a raspberry PI, on which I run OctoPrint on. The two boards are connected over a direct serial connection via GPIO. I took the step on controll the SKR board...

:) [_] Instructions [_] To prevent the holes from sagging, I've designed the stl files with different layer heights. There is one bridging layer in different thichknesses. UPDATE Now also as M5 ISO 4762 available Print instructionsCategory: 3D...

This anti backlash nut is based on a previous design (https://www.thingiverse.com/thing:2634333) and nuts purchased for the HyperCube Evolution (see these nuts in the custom bracket I created here: https://www.thingiverse.com/thing:2630802) This...

... see in the photos but there is a path under the cradle for the wire tie to pass through. The path allows for up to a 6 mm wide x 2.5 mm thick wire tie. This is my HyperCube printer: http://www.thingiverse.com/make:272257 Category: 3D Printer Parts

This is a remix of the hypercube Z Shaft Clamp v1.1 and v2.0. I have remade the original in OpenSCAD and then expanded it. Having one of the bolts behind the smooth rod annoyed me greatly, so this version lets you use either the holes left or right...

This is a Qi-Charger stand I designed. As the original Qi-Charger stands are pretty expensive, I decided to design my own using the electronics I found on amazon. BOM: 6 x M3 x 6 DIN 912 hex srews Wireless Charging Pad: https://amzn.to/2z7ZgAsPrint...

I created this handle to simplify lifting my HyperCube Printer (CoreXY). It's narrower than comparable commercial units, making it ideal for use on 2020 aluminum extrusions. Two mounting holes allow the secure attachment of the handle using 5 mm...

While crafting my own take on a hypercube design, I discovered the necessity to grasp multiple aluminum extrusions simultaneously. At the same time, I needed to secure the screws tightly to ensure everything fit together seamlessly. To address this...

I just wanted to have about the same distance from the nozzle to the bed with volcano and the normal e3d hotend without changing the partcooling. I use the x carriage from this source: https://www.thingiverse.com/thing:2437440 Print Settings...

Walls are 0.8mm thick, the bottom is 0.4mm. The holes are for M3 screws. I also added a short version for pi zero without a makerspot shield, but i didn't test it yet. Print Settings Printer: Hypercube Evolution Rafts: NoSupports: No Resolution: ...

... and should be printed open side up which requires no support. My webcam is now happy to not have dust in its eye :) Print Settings Printer: HyperCube Rafts: No Supports: No Resolution: 0.1mm Infill: 50% Filament: Hatchbox PLA Category: Computer

If you need only an enclosure for the DuetWifi, you can only print this case. The has the possibility to mount a 80 mm fan. As the often used Screw-holes never fit, designed a hole to fit a press nut which can be glued in. Print Settings Printer:...

Here's a good website that explains: https://thekidshouldseethis.com/post/10459448756 Gyroscope not included :) Print Settings Printer: HyperCube Rafts: No Resolution: 0.1mm Notes: Print tab with at least 70% infill and supports. ...Stand can be any...

I created this project because I didn't want to take apart my Tech2C Hypercube frame just to make some taps for adding rubber feet. I think it's extremely useful. I included a safety margin around the extrusions so they don't interfere with the...

The Adjustable Opto-Endswitch Holder is a highly versatile device, specifically designed for use with the Hypercube Evolution Printer. This holder can be easily configured to fit snugly onto aluminum profiles measuring 30x30 in size. To assemble...

remix of thing 2599815 , all credits for the models go to Klomeister. i uses meshmixer to resize the model (with 190mm) , make it hollow with a 2 mm shell and add a 70mm hole in the top. Print Settings Printer: HyperCube Rafts: NoSupports: No...

Designed for hypercube side top down mount of the spool Print Settings Printer Brand: Prusa Printer: Prusa CloneRafts: No Supports: YesResolution: 0.3 Infill: 20% Filament: Generic PLA / PETG Notes: should be about 4.5 hours at prusa 0.3 draft...

This is my remix of a 3030 LED Strip holder for my HyperCube Evolution. It allows you to mount LEDs of varying profiles, both white and RGB, with or without weather seals. There are channels for zip ties. They are deliberately short to allow you to...

So once upon a time I had a burning desire to construct a Hypercube to replace my trusty Anet A8. I took the bold step of ordering five lengths of 1M 2020 aluminum, and after six long weeks, they arrived in 10cm increments. Needless to say, it...

I'm using a direct drive setup for my hypercube so I needed an elevated spool holder and it didn't look high enough on its own so I made a Bowden Riser for it. the Bowden riser uses a PC4-M10 fitting and it is already threaded out for it. Everything...

My design of the ramps 1.4 holder for hypercube 3d printer 2020 extrusion profile is my own creation. This allows you to mount a mosfet for the hotbed and two mosfets module, which are very common from alixpress, to control led fans etc, since the...

I utilized this fan shield on my HyperCube printer, allowing me to place a Plexiglas panel over my electronics bay while still permitting the power supply fan's air to escape the confined area. ...Check out the original design here:...

... ... I designed this one specifically for my hypercube printer to utilize Carbon Fiber on the X axis with 19mm linear bushing. For optimal results, I recommend printing the X carriage Lower Holder with the small "ball" facing up (no support required).

... "easy fit" and should operate well on a well-adjusted printer. Print Settings Printer: HyperCube & CTC Rafts: No Supports: No Resolution: 0.2 & 0.1 Infill: 30% Notes: This spool holder works with PLA & ABS, printed successfully in both materials.

... below or suggest them in the comments. ... Update 19.04.2021 - "added model for linear shafts >75mm" 030.006.002_02 (quick fix - use when needed) Idea HyperCube CNC Toolheads https://www.thingiverse.com/thing:2459624 https://youtu.be/yXVyuvAUqys