hyperstar cable router 3d models
109019 3d models found related to hyperstar cable router.thingiverse
This is a cable router designed for 8" Celestron telescopes equipped with the Starizona, Hyperstar focal reducer. The traditional method of routing cables is to run them straight over the corrector plate. But this results in diffraction spikes. If...
thingiverse
I was annoyed by installing the original version my my scope i ended up using zip ties and thought to my self it would be even better if there were slots for the zip ties so you can easily keep the cables on top. It basically removes the need to...
thingiverse
I was never happy with the stars I got from the commonly used semicircular cable router so I designed this to serve as a slight aperture mask (198mm) and straight vanes to route the cables which give stars a typical newtonian diffraction pattern. ...
thingiverse
I came across this [other project here on Thingiverse](https://www.thingiverse.com/thing:2640393) which is the same idea: a way of routing the USB and power cable for Celestron SCT's with Starizona Hyperstar using a 180 degree arc to avoid the...
thingiverse
Hyperstar Cable Holder and Dew shield for Celetsron 9.25" Edge HD Dew shield for small printers is [here](https://www.printables.com/cs/model/164935-dew-shield-holder-for-celestron-925-edge-hd) Freecad code on...
prusaprinters
Hyperstar Cable Holder and Dew shield r for Celetsron 9.25" Edge HDDew shield for small printers is hereFreeCad code on github BOM16x M3x10mm screwOptionalW&W Astro dew heater 100 cm strapCamping foam mat for create extension...
thingiverse
a simple cable holder, designed to e stuck onto a desk with hot glue, able to route small charging cables
cgtrader
This cable management system allows to secure cables running to your camera on a EdgeHD 925 Hyperstar equipped telescope. There are two models; one that will produice nice spikes to your stars and one that will keep stars perfectly round without...
thingiverse
This is a replacement handle for the Porter Cable router. ...
thingiverse
Quick and dirty cable router for those with the overhead cable system like the KIWI. Make it easier and less stress on the cable's stress relief joint. ...Scale it up or down if it doesn't fit.
thingiverse
Here is the link to the chain: https://www.thingiverse.com/thing:1824144 Here is the link to some of my other cable chain parts: https://www.thingiverse.com/thing:3841900 I was looking to create a way to appropriately manage the power cable for my...
thingiverse
... devices are getting hot and need some distance to surfaces in order to cool down. ...This stand is an easy fix for this problem - just print out four times, place them under your device and the heat is gone. In my case it is used for a cable router.
thingiverse
I modeled this handle for a friend. ...The ones on his router had fallen apart. I know this fits model 690LR. It may also fit others. Maybe someone will find it useful. ...It uses the original bolts.
thingiverse
4 spoked cable router/star mask for Newtonian style diffraction spikes. Designed to fit the ZWO ASI533MC Pro or any camera with similar body diameter. For the C6 Hyperstar, fits inside the Celestron aluminum dew shield. ...Interference fit around camera...
thingiverse
Filter holder for Hyperstar Filter slider Additional parts: You need the circular magnet 5x1mm 2pcs it must be glued to the printed part.
thingiverse
Base Plate for Porter Cable 690 & 890 series routers. ... It has the same 6 holes, plus the center hole also has the required step to accept the brass bushings (see pictures)
thingiverse
I tried to find the handle Porter Cable used to make for the 890 base but it seems to be unavailable so I build one I could use for a router based slab flattening project. It is just a handle not the full dust collector handle. I left all the...
prusaprinters
This is a base plate that fits a Porter Cable router. I needed a larger base plate for a jig so I designed this one with a 7.125 diameter base. (This entry also includes a standard 5.75 inch version in case that's useful.) I used a...
thingiverse
This is a Clip for the Oculus Rift CV1 that routes the cable up toward the ceiling which should help from it twisting and breaking which I have done with 2 cables so far. ...Mostly applies to room scale configuration.
thingiverse
Get it here: https://www.thingiverse.com/thing:3680285--------------------------------------------------------------------------------------------- There is a common problem with the Oculus Rift CV1 that the cable is wearing down after time. So...
thingiverse
... on without disconnecting cables. A revision is planned to add a small section to cover the gap between the cap and the Hyperstar. I'll add the revised version as soon as im able to print and test the fitment. ... For now though, this cover works.
thingiverse
Use this mask to achieve perfect collimation with your Celestron C6 + Hyperstar
thingiverse
The other one is filter holder for hyperstar, I tested these on celestron 9.25 with starizona hyperstar. The third optional file can be glued to the back to make sure no light leaks. After printing and cleaning, I immersed the filter in hot water...
thingiverse
The mask was adapted with Tinkercad to better fit my Celestron C6 with Hyperstar and the Celestron dew-heater ring. I want to credit Satoru Takagi for his work. ... generator can be find at: ...
thingiverse
Wanted something that would wedge the cable in place so i could put tension on them to keep them tidy without using so many. Fits any standard t-slot extrusion. ...STL includes 12 clips and 12 wedges.
thingiverse
This is a simple cable router that slides on to the aluminum frame of the Geeetech Prusa i3 Aluminum variant. ...I personally use it to route my USB cable from the controller board to the rPi.