icom ic 207 3d models
3767 3d models found related to icom ic 207.thingiverse
This is a stand for the Icom IC-7300, placed under the supplied stand it raises the radio by 1". ...
thingiverse
Standfuss für iCOM IC-705 Transeiver. ... Dieser wird einfach auf der Unterseite des Gerätes in die vorhanden Gewinde angeschraubt.
thingiverse
I don't like it when my radios fall over, I built this stand for my Icom IC-T7H to reduce this problem.
thingiverse
My holder for ICOM IC-R30 is based on Rikard´s idea: https://www.thingiverse.com/thing:2890421 and is fully compatible. ...
thingiverse
Useful Stand for the ICOM IC-705 HAM Radio. it can replace the 30 EUR plastics original stand easily. Perfect fitting, incl. Notches for the rubber feet, like the original stand. Backside-stops to prevent the TRX to slip off. STL comes without...
thingiverse
I designed a stand for the small scanner Icom IC-R5. It is designed to be stable with all control buttons available. The DC 6V connection socket is also accessible. ...Silicone lenses can be glued on the underside to prevent them from slipping and the...
thingiverse
Base for Icom IC-7300 Instructions: I printed this in two parts in Cura 4.7 a) Import the two stl files at Cura and align them b) Delete the base and keep only letters c) Generate the gcode d) Undo delete base and remove the letters now, keep the...
thingiverse
This is a volume/squelch knob compatible with the Icom IC-H16T, it uses the same shaft design as the original. The originals use a knurled rubber ring as a grip but I decided to use some coarse splines to simplify printing. A triangular pocket...
thingiverse
This support is for using the Icom IC-2730 transceiver as a base station. Currently, radios for mobile use no longer come with any type of support for use as a base station. The display does not even fit the radio body without purchasing an extra...
thingiverse
Icom IC-705 protective shield. This is a 2 parts shield so it can fit in any 3D printer. Glueing the inserts with "Loctite" or similar is strongly recommended. When printing, use Tree Support and position the part in the bed as in the shared...
thingiverse
I wanted to get a carrying handle for my ICOM IC-718. I found that ICOM does sell a carrying handle, but I figured I would just print my own. I printed it in PLA, but will reprint it in ABS for strength and flexibility. I took a strip of the soft...
thingiverse
This is a pair of rails tha can be attached to the Icom IC-7000 radio in order to protect the front and back of the radio when operating portable.They are mounted to the radio using the same holes and screws used for the mobile base. The length of...
thingiverse
Case for IC-705 for outdoor using. Fixed on the bottom with tripod screw. ...Sliders on left and right side to get access to the connectors.
thingiverse
I hate when my radios fall over, this stand will keep your IC-91A stable when on a table top or other level surface.
thingiverse
Icom IC-705 Antenna Bracket for SO239 connector. ... Antenna strain relief.
thingiverse
Заглушка для отсека гарнитуры для рации ICOM IC-F11. Так же подойдёт к IC-F12, IC-F21 и тп. Пригодится, если комплектная потеряна. Также понадобяться два винта М2 длиной 4-6 мм. ... Напечатана мягким пластиком BFlex (TPU).
thingiverse
Stacking bracket for ICOM IC-7300/IC-9700 transceivers. Wanted to be able to use the tilt foot on the lower radio and a little more space between the units. This bracket (x4) provides the necessary stability and additional air gap. Note the...
thingiverse
A remix of the excellent IC-A4 charger base to use with the Icom IC-92AD amateur radio. ... The correct charger, the BC-177, has long been discontinued; I remixed the charger to make it all compatible with the HT.
thingiverse
The only mic holders for the Icom IC-2730 that I could find were for clipping onto an auto fresh air vent. ... I needed one that I could screw onto a surface.
prusaprinters
The tuning knob on my iCOM IC-A25N aviation radio cracked and broke. ...This is a replacement that's more robust.</p><p>Material: PETG<br>Layer height: .15mm<br>Infill: 100%</p>
thingiverse
this is a stand so you can rest your ICOM IC-28H or IC-28A on your desk. The indents at the top are for thick double sided tape to secure the radio to the stand. ...I have included the sketchup file so you can do whatever you want with it.
thingiverse
I have an Icom IC-705 Radio in a go box, the items in the box sometimes move around, and I needed something that would stay in place. Using the Icom provided model of the radio, with some expansion of the holes for the knobs I made this protective...
thingiverse
A microphone stand for the Icom HM-243 mic/speaker which comes with the Icom IC-705 transceiver. Sturdy enough to hold the mic for easy listening, yet light enough to simply pick up the mic/stand together to chat. Place small rubber feet on bottom...
thingiverse
ICOM IC-2730E ICOM Mobile Transceiver Mounting Bracket. Something similar to original Icom MBA-4. You can mount control head to main body. You can still connect microphone to main body or control head, there should be some room for cables. I...