rcexplorer tricopter 3d models

Custom middle plates and motor mounts for RCExplorers Tricopter V3. Allows you to mount Naze32 Flight Controller. Print all parts from ABS ,solid. You need the following to complete your build( If you don't own the kit) : Aluminium Booms - 12mm or 10...

This is a design for rcexplorer's tricopter v2.5 http://rcexplorer.se/projects/2011/09/the-tricopter-v2-5/ Instructions The two STL files are for the top and bottom of the body of the tricopter. I used 10mm square armatures and bolted the frame...

Custom landing gear for RCExplorer Tricopter V3. Not as durable as the original, but useful while waiting for spare parts to arrive from David :-) Be aware: The original design does not in-corporate the "mechanical fuse" of David Windeståls design...

I grew tired of tie wraps breaking on even a slightly bounced landing with my rcexplorer tricopter. So I developed these flex legs for the tricopter. They will work with any 10mm square tube so these legs are not limited to the tricopter, but any...

When printed with flex filament, this thing is a durable elastic landing gear for the RCExplorer Tricopter. Instead of relying on breaking zip-ties, the elasticity of the landing gears should protect the copter from all but the heaviest landings. ...

This is a remix from David Windestål, the creator of RCExplorer.se: http://rcexplorer.se/downloads/ This front spacer covers most of the integraded naze board. ...Print Settings Rafts: No ...

Tricopter-LR feet for 6mm arms. ...May be compatible with the original 5mm one

Short version of legs for tricopter (10mm booms) - about 50 mm.

... nuts. I've also integrated pin holes to accept similar camera mount isolation hangers as used in the latest design. (http://rcexplorer.se/wp-content/uploads/2012/09/trihv27-2.jpg) I haven't yet assembled this, so I can't guarantee it works at all.

Rcexplorer Tricopter V4 TBS Unify Antenna mount

Summary Rcexplorer Tricopter V4 TBS Unify Antenna mount

Rcexplorer Tricopter V4 TBS Unify Antenna mount Category: R/C Vehicles

Canopy for the RCExplorer tricopter V3 (and mini) Print solid with support. Works best with hex screws at the boom fold. ...Use antenna boom for securing it at the front, barbecue skewer at the back.

:-) Bonus material are two antenna holders for the Rx antennae :-) (boom and 3mm plastic pole) Get the RCExplorer Tricopter V3 frame at http://www.rcexplorer.se Instructions Print the parts standing on the print bed as they would be mounted, with...

Has markings for center of gravity and mount point alignment for screws found on the RCExplorer Tricopter V3 (can be ordered from http://www.RCExplorer.se) Mount with anti vibration tape on frame aligning markings with top row of bolts for the tail...

Kit for tail upgrade - to use DS515M like servo with mn3110 (or similar size) motors with original idea of tail design. ...Also a bit thicker wire holders.

Mount for small VTX (beerotor like - BR25-600). ...Use two zip-ties to mount antenna connector and one - for VTX.

mount for rx

Coffin type Top board, good for 3D printing

Modified nose spacer for the RCExplorer Tricopter V3 to mount RunCam SKYPLUS/PZ0420M board camera.

This camera mount fits on the RcExplorer Mini Tricopter and allows the fitment of a HS1177 camera, and ones of similar form factor. ... 10/02/17 - V2 uploaded, pushes the camera back 1.5mm for easier fitment.

Made a support to screw my betaflight matek f405 board directly to the Tricopter-LR middle plate. ... The support is held to the frame by the tail arm screws and te FC board with 10mm M3 screws

Tricopter or mini tricopter broke a boom? Can't get woven CF box section booms any more? I had that problem after getting my V4 caught in turbulence and then losing an argument with a signpost. I snapped the tail boom in half. You can use 2 part...

Dihedral tilt top for the RCExplorer tricopter V3. Experimental! For use when cutting the arms in half and building a mini tricopter. Derivative of David Windeståls excellent work. Get the frame and necessary servo at...

Mini gimbal that mounts onto a custom camera plate for the RCExplorer Tricopter V3. Get the frame or directions how to build the tricopter frame here: http://www.RCExplorer.se Some parts (camera plate, wire plates) are derived from David Windeståls...

This is a simple and effective way to mount a Tarot gimbal on your RCExplorer Tricopter. There is no cutting or drilling of either the tricopter or the gimbal. Everything can be put back the way it was. Since the gimbal is mounted to the isolated...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/iZa2wKHC2Yi

These are a collection of boom mounts that I've made for various 3DR Ardupilot accessories. ... The camera hinge is designed to work with: The original Crossfire Quad camera Or my GoPro3 derivative case Will be adding more and some pics.

Tool to bend 1.5mm wire into proper shape. I tried doing it by hand and was unhappy with the results so I made this. ...Makes it easier to get the right shape, but it still takes a bit of effort to get it bent right.

This is a remix of http://www.thingiverse.com/thing:1721582. I extended the front "lip" of the spacer, where the FPV cam mounts, in order to accommodate the mounting bracket that comes with RunCam FPV cams (Swift, Eagle, Owl, etc.), because it is...