ikea lack table hacks 3d models

2021 update: Now that I have used these legs for a while, I can comfortably say they have been keeping my Ikea lack enclosure leveled. You only need to keep spinning the legs until you start to feel some force, and almost every time you have reached...

Since the back of my Lack shelf does not have 2 holes, but only one, and the side edges are not symmetrical, I have modified the design to fit my needs.

Screw the adapters to the bottom of the table legs. ... Cut desired length from donor table's legs and insert them into the adapters. ... The fit shoudl be tight enough that they dont need further fixing or glue.

Needed to position my subwoofer under the small table in the living room, but the table was 60mm too low. So, I created this adapter in Fusion360. ... I'm not sure why it's always incorrectly aligned on the table, but I'm confident that you know how to...

The more weight you add on top, the stronger those pieces bind together.Updated 2/28/23Added new Screw-in adjustable feet & legs with a flat bottom by request.Updated 11/08Added new stacking corners & legs so you can make double lack stacks.Updated...

Sound-absorbing solutions for enhancing the stability of my IKEA shelves are being researched and developed. I am preparing to test several prototypes in the near future. ...To optimize the performance of these dampeners, I plan to print multiple units,...

A 275mm x 10mm slot cut into the top of the lack is required.  I created this to use with my Ender 3 V2 with Bondtech DDX.  Because the direct drive was so close to the top of the enclosure, this was the only method I found to keep the filament from...

this is a print bed AC heater wire strain relief part that is modified to have a 90 degree turn, for use with my remixed IKEA Lack Table enclosure, which is also for the BIQU B1, available in two versions here: ***[(V1) For BIQU B1 - DIY Enclosure -...

## Key features * Remove enclosure lack without electrical auto-connect * No door hinges * Use glas sheets as is, no cutting * Pillars to make room for printer baseplate * Clean stacking feet solution (Does NOT protrude!) ## BoM (Bill of Materials) *...

Also, it does not depent on how far the screw points of the PSU are apart. This adapter is needed two times for proper attachment of the PSU. What you need:2x     3,5 mm screws       (to connect the PSU to the adapter)4x     4 mm screws          (to...

I deliberately skipped using the holes for screws on the bottom table, but it still turned out great. The print quality was excellent. It's essential to use supports when printing this item. ...Print Settings: Printer Brand: Wanhao Printer Model:...

With this modification, you can attach the stackers directly to the corners of your table without needing to screw anything into place, making it a quick and easy setup process. ...Alternatively, my table might have been uniquely constructed, which...

I have not been able to find 40x44.5mm acrylic cuts where I live so I improvised doing some supports based on the stands designed by wbronner. There is a version that can runs along the border of the table and another one that's mounted like the...

For each of the more space required under the lower table, these increases are optimal. In version 1.1, the holes were a little too small for me, so I added a little bit to them in V1.2. In the picture, however, they have been installed in V1.1...

I carefully consider each space requirement below the table and make adjustments accordingly. In version 1.1, the holes were slightly undersized for my needs, so I enlarged them in V1.2. ...Yet, as shown in the picture, they are actually installed in...

... very top, the filament crosses a lot in the original grommet, this grommet allows the filament to bend at a larger radius. Better to make a bigger hole in the bottom of the table, ideally 91mm, maximum 100mm to cover the collar of the lower part.

Here is some additional material you need: - 1x clothes rail (mine is from IKEA) - 6x universal screws (TX 10 3,0x12) You can mount the filament spool holder directly under the shelf (as you can see on the pictures) or you can use version 2 to mount...

The Tush with the lock for the Lack case. Print one of the part here and 3 of the originals from here: <a href="https://www.thingiverse.com/thing:2047554">https://www.thingiverse.com/thing:2047554</a></p> <p>One part of the spool holder then locks...

The Tush with the lock for the Lack case. Print one of the part here and 3 of the originals from here: https://www.thingiverse.com/thing:2047554 One part of the spool holder then locks into place with the lock of the case:...

Once printed, they will go into the collection.\r\n\r\nYou'll also need to print four upper corners for the top table.\r\n\r\nFor the top and bottom tables, I used super strong magnets that are 4x1mm in size. ...To accommodate these magnets, I created a...

There is also filament cleaner on top inside the table, just cut and put the foam inside. Double sided tape is used to put locks on the glass. ...   I dont like the hinges, because I dont always use closed printers, so for me is better to just put the...

Here is a very quick design to clean up the top table and reuse its space. The main goal of this spool holder is to tidy up the workspace and make the most of available room. Print 2 units using the same m8 rod from the original Anet A8 spool...

Print: 4 leg_wood_wood 2 leg_wood_plex 2 leg_plex_wood Support Spool: https://www.thingiverse.com/thing:4398804 Hinge: My PLA hinges broke, so I recommend metal hinges instead Handle: https://www.thingiverse.com/thing:12695 Screws for handle:...

I originally printed a design for an Air can holder, a design I can't find here, and was satisfied with how convenient it was to store the Air can next to the table. But I also have a bottle which is always on the ground for the cleaning of the print...

... do decide to use it. There are two files available: footdoorright and footdoorleft, which I plan to use for the future enclosure front door. The foot is simply one of those standard feet that can be used to level tables or connect them together.

12cm table feet spacers can be found at: https://www.thingiverse.com/thing:2127786 A filament guide can be downloaded from: https://www.thingiverse.com/thing:3129612 Hobby glass panes, 500x500mm in size and 2mm thick, are available for purchase at:...

12cm table feet spacers can be found here: https://www.thingiverse.com/thing:2127786 A filament guide can be accessed via this link: https://www.thingiverse.com/thing:3129612 Hobby glass panes are available at this online retailer:...

I originally printed a design for an Air can holder, a design I can't find here, and was satisfied with how convenient it was to store the Air can next to the table. But I also have a bottle which is always on the ground for the cleaning of the print...

English version This is a heigth inserts for the original project: for table's legs, 11cm high for walls, 5cm high (in case you use the same acrylic glass as is suggested in the original project) Why I made it: I've build a thermal enclosure for my...

# English version This is a heigth inserts for [the original project](https://www.thingiverse.com/thing:5019633): - for table's legs, 11cm high - for walls, 5cm high (in case you use the same acrylic glass as is suggested in the original project) #...