inductrix fpv plus 3d models

Check out this Thingy https://www.thingiverse.com/thing:2814692 While the pictures are of the thicker walled version of a case for the FPV Plus case, you will find thin walled versions as well. You will find a variety of cases for the FPV and FPV...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/b4A5uuXsRvt

Work in progress.

A camera mount for Blade® Inductrix® FPV plus frame.

A travel case I made for my Inductrix Plus FPV. Requires 8 2.5mm diameter magnets for holding the lid on. ...I used foam on the lid to put slight pressure on the quad to hold it so it would not flip over if the case gets tipped.

X-Brace for Blade Inductrix FPV+ (Inductrix FPV Plus, red frame). Stiffens the frame substantially vs stock. When installing, route wires through notch; make sure not to pull on motor wires too much. Designed to be a very tight fit. < 1gram...

For the version shown, which is 2 FPV Plus Cases and 4 FPV/FPV/ Pro cases, print 2 each - V22 FPV Plus Bottom Thin 4each - V22 FPV Bottom Thin 1x - V22 1st, 2nd, 3rd & 4th Insert Next up, I'm designing an insert for a 4 way charger, and also for the...

... 5.8G 48CH 25mW Transmitter Inductrix Mount" at https://www.thingiverse.com/thing:3027427. Example build can be found at: https://johnbrisbois.com/content/tiny_whoop_inductrix_fpv_plus_flight_controller_build https://rotorbuilds.com/build/13682

... Inductrix FPV Roomy AIO Camera VTX Canopy Cover" at https://www.thingiverse.com/thing:3032794. Example build can be found at: https://johnbrisbois.com/content/tiny_whoop_inductrix_fpv_plus_flight_controller_build https://rotorbuilds.com/build/13682

Case with lid for Inductrix FPV+. ... Holds Inductrix FPV+, 16 1S Battery Packs and USB Charger.

Case for the Inductrix FPV +, 7 lipos and charger

These brackets are for the Blade Inductrix FPV+

This is a container for an Inductrix FPV (not FPV +). ...It holds the Inductrix itself and has slots for 4 batteries and a charger unit.

... Micro Swift/TX200U VTX combo with inductrix/tiny whoop screw pattern. ... Example build can be found at: https://johnbrisbois.com/content/big_whoop_inductrix_fpv_plus_flight_controller_850_runcam_micro_swift_2_build https://rotorbuilds.com/build/14595

Are you tired of your Blade Inductrix FPV+ props flying off? The central shaft most likely cracked, these little donuts keep the shaft tight so that they don't crack and fixes broken ones if they are printed just right. This simple print uses...

I designed this box to hold the Inductrix with an FPV camera on, it's also got space for 10 batteries. Enjoy but beware it's a long print. ...Print Settings Printer: SmartrapcoreXY ...

... I attached the Fusion 360 file. I'm not very experienced with it, so I'm sure it can be improved upon. The current model has the text "Inductrix FPV" embossed on one of the faces. ...That's easy to remove in Fusion 360 if you prefer not to have it.

This is a frame stiffener for the Inductrix FPV. It will save you a few broken frames from hard landings. It should be a nice hand press fit and has clearance built in for the motor wires. The web is 1mm wide and 5mm thick. It gives great rigidity...

Carry case for Inductrix FPV pro and 9 batteries. Extra space for the USB charger and miscellaneous. ...Designed in Sketchup (files included).

Designed this wall mount for my Blade Inductrix FPV micro drone. ... I install mine on the wall using two push pins (thumb tacks) Print Settings Printer Brand: MakerGear ...

Took this thing http://www.thingiverse.com/thing:1725373 and stretched it to fit the blade inductrix fpv. ...i might even remix it further adding another compartment or adding battery slots or both Print Settings Printer: Anet...

I created this brace to protect the frame of the Inductrix FPV+. There are 2 versions, the wall thickness is the only difference. V3 is the lightest. If you have trouble printing this, then please try V2. The brace should slide over the...

This is a great case I designed and printed for the new Inductrix FPV. It will hold the Inductrix, 20 batteries, 7 USB chargers and has a slot for miscellaneous cables and tools. The lid has a big Tiny Whoop logo on it. I am not sure of the clearance...

https://www.amainhobbies.com/blade-inductrix-fpv-replacement-parts-racing/c10476 Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: Yes Resolution: 0.1 or 10 microns Infill: 100% Notes: This little part has alot of...

A very basic and lightweight frame for the inductrix FPV Pro. 6 mm motor mounts. I have omitted the battery mount and opted for a simple elastic band to secure the battery. This saves weight, and places the battery as close to the COG as...

This is my take on battery caps for the 3.7/3.8v lipo batteries for the Inductrix FPV (what I have) or the tiny whoop (it's my understanding this should work too) I printed mine in Ninja Flex. Perfect fit really depends on the battery. I used some...

PLEASE NOTE: I have uploaded an FPV Plus version of the case here: https://www.thingiverse.com/thing:2801903 I have completely re-worked the files, and optimized for printing. I did a true offset, so now the round corners are parallel. The walls are...

Replaces the Inductrix FPV canopy Saves weight for longer flight times Laydown mount protects vtx and reduces overall height

I made a variant of the snap camera mount by S_Smitka for the Blade Inductrix FPV's stock camera, camera angle is 20 degrees, I had to "pinch" the sides of the camera mount inwards to hold the camera securely, and added a third screw hole at the back...

This is a alternative camera mount for the Inductrix FPV. This mount allows for easy mounting to the Inductrix frame, as well as easy snap-in/lock for the camera and it's transmitter. The camera mount is design to be at a 10 degree angle. ... Print...