inkbird controller 3d models
88608 3d models found related to inkbird controller.thingiverse
This is a two part case of an Inkbird temperature controller. It's compatible with the ITC-2000 and the ITC-1000, although the former only controls one relay. You can use the second hole to wire up a straight outlet that's not controlled by the...
thingiverse
I wanted an all-in-one case for my inkbird temperature controller for use with home brewing. I designed this to be able to have the controller visible from the front, and the outlet ports on top, using standard duplex outlets, not the single...
thingiverse
Simple holder for an Inkbird temp controller for my homebrew fermentation chamber. ...Has a spot for a pencil and a sticky pad, for notes like temperature schedule.
thingiverse
... I have laying around. You'll only need the following parts - [Inkbird ITC-2000](http://amzn.to/2gHLI65)\* [Power Inlet](http://amzn.to/2yRTylJ)\* Two screws from your junk drawer for the inlet. ... [Surface mount plugs](http://amzn.to/2y6Gcox)\*
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: FPanel = 1 Filet = 2.1 BShell = 1 PCBFeet = 0 FootDia = 8 BPanel = 1 Height = 86 Length = 150 m = 0.9 FootHole = 3 PCBLength = 70 TxtSize = 5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: PCBPosY = 6 PCBPosX = 7 Police = Arial Black Width = 131 Length = 150 FPanel = 1 Height = 86 Text = 1 TShell = 1 FootDia = 8 PCBWidth = 50...
thingiverse
I liked the design from the original but I did not like that the plug-in ports came out the top so I redesigned it to have the power the temp probe and plug in come out the back for a more sleeker look I printed mine with 20% infill and with a...
thingiverse
This is a Remix of the top for https://www.thingiverse.com/thing:2193849 with "HEAT" and COOL" added above each outlet.
thingiverse
Inkbird temperature controller enclosure that I've lengthened and added feet to so magnets can be used to attach to appliance and make more portable
thingiverse
A case for Inkbird ITC-1000 (or ITC-2000): ITC-1000 is a temperature controller used to regulate temperature via a cooling fan into a closed enclosure (based on IKEA LACK) of a 3D printer.
thingiverse
Amazon search for PID ended up showing the Inkbird ITC-1000 ( which is not a PID, I didn't realize that when i bought it) I liked the 10A contact rating for the internal relay, so i got one and had to figure out how to mount the 'PID' controller. I...
thingiverse
This Inkbird controller system is wireless WiFi and allows me to manage and control the heating system remotely. The controller has an Android app that's pretty awesome. I also created a mounting bracket to secure in place the relay controlled...
thingiverse
Remix of Thesquirlmaster's case with additional mounting holes in the sides.
thingiverse
Remix of InkBird fridge holder by copter1 and Inkbird Power socket holder by dagobert_ch. ... This holds both the InkBird controller and the power sockets.
thingiverse
I am using the Inkbird to control an exhaust fan mounted in my 3d printing cabinet. I printed this on my Creality printer using PLA set to 20% infill, and a table temp of 60 degrees, and extruder temp of 250. Make sure you check your pla...
thingiverse
I created support for this thermostat inkbird:http://www.ink-bird.com/product/detail/p/PID_Temperature_Controller_ITC-100/id/7...
pinshape
Summary I created support for this thermostat inkbird: http://www.ink-bird.com/product/detail/p/PID_Temperature_Controller_ITC-100/id/7...
thingiverse
This is a remix of "Inkbird Temperature Controller Box by markag". I added four mounting tabs with thru-holes for hard-mounting the box to a flat surface. That's it! ***I've included a picture on how to wire the Inkbird ITC-1000. ...I am not...
thingiverse
While in the process of building a standalone PID controller for a small Powdercoat oven. I cut the opening for the InkBird ITC-106 a little too big. So I designed this bezel to take care of that issue. ... Bezel extends 5mm in all directions with...
thingiverse
INKBIRD 4X weber mount. ...Quick desing for the inkbird 4x thermometer allowing you to attach it to the weber leg. ...Please upload a photo once you have printed would love to see these out in the wild.
thingiverse
Designed this probe holder so my thermometer probe would stop from tangling. ...It works with the Inkbird/Thermopro style probe
thingiverse
... PETG with .2mm layers Prints without supports if oriented as shown in the pic. Sensor: https://smile.amazon.com/Inkbird-IBS-TH1-Wireless-Thermometer-Hygrometer/dp/B0895KGHFL/ref=sr_1_4?dchild=1&keywords=inkbird+ibs-th1&qid=1627825283&sr=8-4
thingiverse
Mein erstes THING Eine Box für das Grillthermometer INKBIRD-IBT-4XS Einfache Box zum Ineinanderschieben. Die Teile halten ohne Kleber. Ausschnitte auf der Geräteseite für den EIN/AUS-Schalter und die Ladebuchse. ... ...
thingiverse
This is a simple case for my Inkbird IBT-2X bluetooth BBQ thermometer. It is designed to hold the thermometer itself and the clip for the probe. The probes are not contained in this case. ...Instead I am using two 18.5x3mm magnets to clip those [probe...
thingiverse
Die Wahl fiel hier auf den Inkbird ITC2000.https://www.amazon.de/gp/product/B0185M6I28 Da das Gerät jedoch ohne Gehäuse geliefert wurde und die Anschluesse eher Bastlercharakter hatten, habe ich mich entschlossen ein Gehäuse zu kreieren. Die hier bei...
thingiverse
A housing for the ITC-306VH PID controller, for mounting it to the side of something else (like an espresso machine).
prusaprinters
Junction box lid to hold the Inkbird ITC-1000 temperature controller and 120VAC outlet. ...Fits the new 4"x4"x4" junction box found in home improvement stores.</p>