instax scan adapter 3d models
180412 3d models found related to instax scan adapter.thingiverse
Here is a simple adapter to use both instax wide and instax square on the same camera! The actual version is made by 2 parts - Element that push the film package - Base element with the 2 shape design (the actual version available is still...
thingiverse
I found the 3d project for adapting the instax wide camera to use instax square film, but it was for the instax 100, which has a slightly different push mechanism to the 210. This is just the push element as I am still working on the base element and...
thingiverse
Print Settings =========== 0.2mm layer height Made with ESun PETG 30mm/s print speed Infill 100% Support raft enabled Credits ======= Remix of Instax wide 200/210/300 adapter to square by viper8924. Big shoutout to them as they did the hard work and...
cults3d
Instax Wide 300 self-timer adapter using a Polaroid self-timer #192 . I really needed a way to use a self-timer on the Wide 300, you can easily buy a self-timer 192# on ebay. I had to mod it tho, I easily welded the tip of a pen at the pushing pin...
thingiverse
Instax Wide 300 self-timer adapter using a Polaroid self-timer #192. I really needed a way to use a self-timer on the Wide 300, you can easily buy a self-timer 192# on ebay. I had to mod it tho, I easily welded the tip of a pen at the pushing pin...
prusaprinters
An adapter to use 52mm filters with an Fuji Instax mini EVO. It just pushes onto the lens barrel. A previous design was too tight and could pull off the lens barrel when removing the print. </p><p>CAUTION: to remove use your thumbnail to push...
prusaprinters
The film-back holder seemed like a perfect size for the Fujifilm instax-wide film sheets, so I decided to make an adapter or template (still unsure which word fits best) so the film-pack holder could use instax-wide film.There are 4 parts to this...
thingiverse
... ...The adapter can be screwed/glued on the back of a Graflex 3x4 camera for a Lomo Belair INSTAX wide back. You will find all 3d parts which are required for the modification. 1. INSTAX back adapter 2. Focus Screen adapter 3. Focus Screen bezel 4.
prusaprinters
You will find all 3d parts which are required for the modification. INSTAX back adapter Focus Screen adapter Focus Screen bezel Crank adapter For the installation required: Glue (like SuperX) Several Screws Leather pieces More photos and details...
thingiverse
I saw keigo21's design for the instax 100 and decided to make one for my instax 210, basing it on his design but heavily modifying it. You need to print the push element vertically with supports, and also with as much detail as you can, since...
prusaprinters
Also the film is wavy throughout the surface and can vary 0.65 - 1mm from center to edges.Just make sure that it is 15.30-15.35 and no less, but no greater than 15.5mm from where the lens seats on the adapter, to the bottom of the adapter. This...
thingiverse
This design is based on keigo21's design of the adapter, with many improvements, making it easy to just print and then mount it. To mount it just remove the screws from the original piece, take the springs, put them on the new push elements and...
thingiverse
This is a scan adapter I made so you can scan polaroid pictures without newton rings. Feel free to change it to your needs. All you need is a little bit of double sided tape or just tape folded over on itself to stick the photo to the back of the...
thingiverse
... better to print the main part in its entirety. The main and protrusion parts together form a small groove to insert the dark slide. More details here: https://theamateurengineersg.wordpress.com/2018/03/07/adapting-instax-wide-back-to-4x5-camera/
thingiverse
Raises the film off the glass to prevent newton rings when scanning instant film. Use any poster tack in the circular recesses to hold the film. Use the large center hole to push your film back out when complete. ... (I prefer loctite...
thingiverse
Good news everyone! ... Here is the third remix of my series of storage boxes and frames for instax photos! ...hope you like it, now it includes a version for the instax square and is more stackable!
thingiverse
... and put the cover on the adapter at the device output slot. 6. Use the 2 holes and cable tie to fix in position. 7. When scanning is completed, remove the cable tie and cover first before removing the scan adapter and holder. ... See pictures!
thingiverse
This is a simple adapter for APS films for the Reflecta x33-Scan film scanner. ** IMPORTANT: ** You absolutely need to print this with transparent filament. See [this artcile on my...
thingiverse
... send me a message and I shall make the adjustment. ### Contact View my Polaroid (scans) on https://polaroidception.com View my professional profile on https://www.linkedin.com/in/timvandenbelt/ View my personal profile on https://timvandenbelt.com
thingiverse
... send me a message and I shall make the adjustment. ### Contact View my Polaroid (scans) on https://polaroidception.com View my professional profile on https://www.linkedin.com/in/timvandenbelt/ View my personal profile on https://timvandenbelt.com
thingiverse
- New adapter to keep film in the right position (possibility to apply a soft cushion). With holes for attaching cable ties. - Movie frame is now the size of the frame (no overlap). - The main part must be printed only once. ... Adjustments can...