jdm license plate bracket 3d models
308471 3d models found related to jdm license plate bracket.thingiverse
Japanese ("JDM") license plates have slightly different dimensions and hole spacing than North American (US/Canada) plates. This adapter installs onto the original plate mounting locations on a JDM vehicle and allows installation of an NA plate. NA...
thingiverse
This is a single piece adapter to allow you to mount a North American license plate (7in center to center mounting holes) to a car with JDM mounting points (210mm). ... In order to use this solution, you will need two countersunk M6 bolts to connect to...
thingiverse
Remixed this (rebuilt using original as a guide in Tinkercad) with some slight size revisions. ... Changed the proper license plate bolt to be an M6 bolt as well, adapted the nut slot to be a bit tighter for fitting an M6 nut.
thingiverse
License plate bracket with or without light housing. ...Fits on Stock Chopped rear fender.
cults3d
License plate bracket with or without light housing. ...Fits on Stock Chopped rear fender.
thingiverse
This Adapter allows you to put Canadian(or NA) License plate onto your JDM vehicle. It was designed for my Subaru Legacy B4/GTB. The bigger hole is for M6 bolt, a smaller M5 to hold the license plate, you will need a washer for it. It will also...
grabcad
This is a universal license plate bracket that can replace most stock brackets on cars. ...Most stock brackets are flimsy and do not last long, but this bracket is designed to resist the common stresses put on the license plate bracket.
thingiverse
... ... Bracket interlocks two North American size licenses plates together via the screw holes. ... After some trial an error, v2 seems to work a little easier putting the plates on and off.' v3 is for the top-most plate or to hang single plates.
thingiverse
... with just one corner warping. Use the 2 bolts that connect to your car and all you will need is: A drill (to drill holes at the appropriate lengths for your car) 2 bolts (to clamp license plate to bracket) 4 washers 2 knuts oH! ...and print this...
cults3d
Für österreichische Kennzeichen (höhe 120mm) For License plates (height 120mm)
thingiverse
license plate holder for trailer Print Settings Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: .20 Infill: 20
thingiverse
I bought my motorcycle used- the previous owner had cut the stock licence plate holder off directly below the rear tail light and had a sketchy/illegal mount. I didnt really want to run with this, so... created a new one that matches up with the...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=52757 Instructions Using the following options: text_depth = 4 font_scale = 1.5 top_word = Mountain Home plate = 155.9 bottom_word = Bombers
grabcad
License plate bracket for those who have removed or replaced their stock rear tail light on their Honda XR650L. ...Distance between the license plate mounting holes is 145mm.
thingiverse
This 3D Printed License Plate "Frame" allows you to proudly display your fine Japanese automobile's Mazdaspeed heritage without actually claiming you're fast. SHOULD bolt on perfectly to all American license plates. Probably bolts onto license...
thingiverse
License plate bracket to replace the factory plate holder on the 2016-2018 Ford Focus RS. Allows for the use of standard 5mm stainless hardware (M5-0.8x12) without the risk of scratching your paint with screws that are too long. ...Uses the factory...
thingiverse
I also passed a zip tie through the lower bolt holes of the license plate, secured the free end with a zip tie head, and ran a zip tie around the lower portion of the bracket so that the license plate would be flush with the car. ... If you bought a...
thingiverse
Many Hummer H3 vehicles don't have a traditional license plate holder on the front, they just have these plastic square brackets that you screw into. ...If one or both of yours is broken, you can print this replacement.
thingiverse
... Accord Coupe. Also I wanted to mount the bracket behind the license plate, not in front. (Some states will ticket you if the plate is obscured at all.) This design was done in OpenSCAD and you can customize it! All dimensions are in mm. ...
thingiverse
We picked up a few novelty plates, so to display them I whipped up few simple brackets. I made a 3-hole and a 1-hole version, depending on preference (I prefer 3, because hey...options). I had the best luck printing them flat on their back, so I...
thingiverse
... should fit any 1050, 1190 or 1290 Adventure. ...Designed for M6 countersunk bolts. The KTM logo gets covered by the license plate but hey, you bought a KTM, you'll probably print this with orange filament even though literally no one will notice it.
cults3d
Attach the license plate to the holder using bolts/screws and placing a washer between the license plate and the holder. This washer is important to avoid placing undo stress on the holder and to avoid having the bolts come into contact with your...
thingiverse
Attach the license plate to the holder using bolts/screws and placing a washer between the license plate and the holder. This washer is important to avoid placing undo stress on the holder and to avoid having the bolts come into contact with your...
thingiverse
Wanted to clean up the way I had my License Plate mounted on my 2002 Ducati Monster M750S. This is for Monsters with the tail chopped. The holes are sized for M6 hardware. I did have to add about 10mm of spacers to clear the frame. That also...
thingiverse
There are two versions here: Plate Bracket.stl and .skp is the skinny version that I'm currently running Plate Bracket with Turnsignal.stl and .skp is the fatter version with mounts for stock 99-02 Suzuki sv650 front turn signals and rear reflectors....
thingiverse
A set of JDM-stylized license plates, made in the dimensions of original japanese vehicle registration plates (330mm wide and 165mm tall) without any holes or other modifications (left our to best fit your use-case). I have misplaced my original...