jetson nano case 3d models

Jetson Nano case

jetson nano case

GitHub link: https://github.com/dudasdavid/Jetson-nano-case Features: - Antenna mounting points for Intel 8265NGW Wireless-AC 8265 NGFF 802.11ac 867Mbps 2x2 MU-MIMO WIFI BT 4.2 Card - Lightpipe hole for status LED - 2 buttons for rerset and power -...

# Jetson Nano Case A minimal snap-fit case for the Nvidia Jetson Nano. The original design was very well done, but I prefer cooling over the logo. This is for the 4GB kit with all the ports, but I imagine also fits the 2GB kit. ## NanoBox...

Jetson Nano CaseA minimal snap-fit case for the Nvidia Jetson Nano. The original design (<a href="https://www.thingiverse.com/thing:3603594">thing:3603594</a>) by <a href="https://www.prusaprinters.org/social/17411-ecoiras/prints">ecoiras</a> was...

NVIDIA Jetson Nano case with camera holder(IMX219-160IR) I have used small 60x60 CPU FAN as well, you can edit source file if you have different fan or you can use it without fan at all if your Jetson Nano is not running under heavy load. Fusion360...

Based on the Jetson Nano Case by ecoiras, I extended the model with a seven segment display like number. We have a lot of Nanos and wanted numbering on the case. If you want to change the numbering open the f3d-file, double-click the last extruison...

NVIDIA Jetson Nano case with camera holder(IMX219-160IR) I have used small 60x60 CPU FAN as well, you can edit source file if you have different fan or you can use it without fan at all if your Jetson Nano is not running under heavy load. ...

NanoBox - ABS Edition A variation of the Jetson Nano case that should be easier to print in ABS and other warp-prone filament materials. Bluecake found that warping would make some of the finer walls snap when printing the original model in ABS.

... [Bluecake](https://www.thingiverse.com/bluecake/about) pointed out printing this model in ABS is quite a challenge. I made a new version that should be easier to print: [Jetson Nano Case - ABS Edition](https://www.thingiverse.com/thing:3649612)

**NanoBox - ABS Edition** A variation of the Jetson Nano case that should be easier to print in ABS and other warp-prone filament materials. [Bluecake](https://www.thingiverse.com/bluecake/about) found that warping would make some of the finer...

Jetson nano Case for B01 Assembly instruction video https://youtu.be/iDhCWCOdKTI Filament PLA: Black and Transparent PETG: Transparent green (used in the frame area where heat is applied) Print settings Support: none Infill: 20 percent What else do...

Case for Jetson Nano

I drew up a basic case for the Nvidia Jetson Nano. It's designed to be small, lightweight, and durable. It's intended to prevent shorts and damage, not to completely cover the board, so you can throw your Nano in a backpack without damaging it. It's...

NanoBox: a simple case for the Nvidia Jetson Nano. I left an opening for the heat sink at the top, which should permit attaching a fan using the screw holes already in place. There is also an opening at the back for easy access to the microSD card...

wait for the V2 ------------------------ Case for the Nvidia Jetson Nano Developer Kit. Hole on the right side for the GPIO connector Holes on the left side for the camera ruban and pins cables 19/04/03 --> this is a prototype, not printed...

A remix of Ecoiras' NanoBox case [which you can find here.](https://www.thingiverse.com/thing:3518410) Changes include: - Removed hexagon mesh in back panel to make printing/removing support easier on less-accurate printers - Replaced hexagon mesh in...

A Camera mount that slides into the slot of the [Jetson Nano Case](https://www.thingiverse.com/thing:3649612) For the [Jetson Nano Developer's Kit](https://developer.nvidia.com/embedded/jetson-nano-developer-kit) This is a mount for the [IMX219-120...

A Camera mount that slides into the slot of the Jetson Nano Case For the Jetson Nano Developer's Kit This is a mount for the IMX219-120 Camera for NVIDIA Jetson Nano which has the cable on the top side and lens in a different place than other mounts...

A very simple camera stand to be plugged on [ecoiras jetson nano case](https://www.thingiverse.com/thing:3603594). ... To fasten the camera to the stand you will need [M2x8mm fastener screws](https://www.amazon.com/dp/B00YBMRAH4/ref=cm_sw_su_dp) [Some...

Remix of ecoiras' Jetson Nano case that replaces the NVidia logo with slot for one of the cheap 0.91" SPI 128x32 1306 OLED boards that can be had for a dollar or two on eBay or amazon for when you only need a little info from the Jetson and want to...

The case captivates through its simplicity and ability to use it as base for your own custom build: [Top](https://www.tinkercad.com/things/icH0cmrKAFM-jetson-nano-top), [Bottom](https://www.tinkercad.com/things/0BthqyZGkF3-jetson-nano-bottom)...

NanoBox -- Connectors' Edition A remix of the NanoBox Case for the Nvidia Jetson Nano Developer Kit with more precut slots for connecting stuff. Apart from the slot for the expansion header already in the original NanoBox, this version includes...

Modified button to have an extra 5 mm below the nano for reasons. I should add I have not printed it yet. ...Should be fine as only the button was moved and no interfacing areas where the cover meet were modified.

Otherwise the case slides into place. It's a bit tricky to align all the panels. It is solid when assembled but does not snap tight. My printer was having trouble printing the back panel cleanly, so there are a couple simplier versions provided,...

Jetson Nano case with VESA 100mm mounts. Modified/simplified to make it easier to print. ...Also relocated the antenna holes and made them permanent (and not knock-outs).

Nvidia Jetson Nano 2GB Case(Enclosure) with mounting holesCase has a snap in lip/groove design, no need to have additional fasteners. ...Will add camera ribbon feature in next model.

Jetson Orin Nano case I made for myself, I haven't done printing the top part yet so I will update this after testing. Bottom part has 2 versions for one with PCI slot screw holes and the other is without them. ... Feel free to delete the mark...

This remixed version has the following changes: - the holes made hollow so you don't have to make cut them yourselves (all antenna holes, cpu fan holes, and pinout holes) - the 4 rods on the top part have thicker fillet to prevent them from...

WIP