jonbot plus printrbot plus inspired 3d printer

Print Settings Printer Brand: Printrbot Printer Model: Printrbot Plus Rafting Not Required: Doesn't Matter SUPPORT NOT NEEDED Additional Printing Notes: 1. Use 2-3 wall settings. 2. The extruder needs a squirt of WD40 for the machine to run...

This text describes a Solidworks design for an upgrade to a Printrbot Plus V2, replacing the stock belt with a GT2 belt and improving tensioners. The designer purchased the new belt and pulleys on eBay for approximately $30. To install, print four of...

A 1 kg spool holder is available for the UP Plus 3D printer, ensuring easy management and organization of filament during printing.

I upgraded my Printrbot Plus v2 with the ACME leadscrew upgrade from Printrbot.com, but the new ACME nut wouldn't fit within its holder due to size constraints. To resolve this issue, I carefully measured the nut and designed a custom nut trap that...

This minimalist bracket mounts a fan on the Printrbot Metal Plus. I designed it because, in my opinion, the stock Printrbot fans perform just as well in an open-air setup as they do when enclosed. These fans don't produce enough pressure to compress...

A simple Y belt tensioning device for the Printrbot Plus V1, designed to utilize extra screws/nuts/washers included with the kit. See "Y_Belt_Tensioner_Instructions.pdf" for instructions. ... UPDATE - 7/5/2015 Installed a week ago, and have observed no...

Secure your caliper's 16mm shaft to the Printrbot Plus' rails, enabling precise bed leveling. Insert it into the designated slot and attach it to the x carriage rails. Zero the caliper at a print bed corner and measure as you move it around for...

The Printrbot Plus Z-Axis Motor Coupler is a replacement for the existing two-piece option, offering simpler maintenance of threaded rod alignment. This improved design ensures better performance compared to the original coupler. ...To use it, print the...

The Printrbot LC and LC PLUS feature a simple stabilizer design that significantly enhances the rigidity of the entire frame. Additionally, it includes an extruder mount as depicted in the photograph. The required Bill Of Materials (BOM) consists of...

I upgraded the standard ceramic hotend on my Printrbot Metal Plus with an E3D V6, which performs flawlessly. Not utilizing a spacer was a deliberate decision, considering the original fan shroud proved ineffective anyway. ...Instead, I designed and...

To create an aluminum bed caddy for my Printrbot Plus (V2), I chose 5mm plate due to its warped wooden base. The inspiration came from a thingiverse design (http://www.thingiverse.com/thing:91504). The caddy sits over the stock bed, utilizing...

Assembly instructions are available here: http://printrbot.dozuki.com/Guide/Printrbot+Plus/24/1?revisionid=HEAD. Note that files initially lacked the Y-Bar piece but have been corrected, and an alignment error was fixed on 02/07/2013. ...The original...

These parts provide a means of mounting two PrintrBot Alu direct drive extruders on a PrintrBot Plus version 2.1 (1311) printer, although they may work with older models. They will not function properly on any Plus with the X-Z upgrade; I plan to...

This is a collection of enhancements made to the Printrbot Plus 1404 model. These can be either laser cut using the included .DXF file or 3D printed with the aid of the provided .STLs. The following components are part of this bundle: Extended...

Create a custom-designed mount for your Printrbot LC PLUS's smart controller. The stock model doesn't support smart controllers, so this design is perfect if you're using an alternative to the RAMPS board like Printrboard. ...Printed at 0.3mm layer...

Revise the extruder stepper fan bracket of a Printrbot Plus (2013) to enhance cooling. The 50mm fan-compatible design requires only 4mm screws - 2 x 8-10 for attaching the bracket and 1 - 2, 20mm for connecting the arm. ...To secure the arm to the...

However, this design was optimized specifically for use with the Printrbot Metal Plus (1412). To print your spool stand, you'll need four standard 608 bearings and nothing else except possibly sandpaper. The bars in my spool stand are designed to...

I noticed that my PrintrBot Plus V2.1 would have problems printing very tall objects - towards the top of the Z axis, the small amount of wobble of the z-axis guides is pronounced and leads to the sides being slightly closer together. This causes the...

Here is the original text: A simple mount for a Logitech C270 webcam that mounts directly onto the PrintrBot Metal Plus case. You can use the existing machine screws (there is enough thread or you can buy slightly longer ones up to you but I have...

This set is perfect for V1 Printrbot Plus as it matches the screw hole pattern precisely; other sets failed to do so. The OpenSCAD file is provided. A diagram of Z-Axis holes' dimensions is included...

... to the extruder, which was the reason my previous fan stopped functioning. I recommend using a cable chain, available at https://www.youmagine.com/designs/printrbot-metal-plus-cable-chain, to alleviate these issues and ensure optimal performance.

... wide length filament clip. For more info you can visit at our site: http://www.supermotoxl.com/Real-object-design-for-hobby-models/3D-printed-real-object-design-for-hobby-models/xl-rcm-120-filament-holder-kit-for-up-plus-3d-printer/menu-id-118.html

Easily upgrade your Printrbot Plus to Richrap's quick fit system by just replacing the topplate of the original extruder mount. This enables you to still mount the original extruder without the old topplate or with the supplied adapter, the quick fit...

This adaptation involved modifying an existing diamond hotend carrier, taking into account the specifics of my Printrbot Plus V2 (version 1306). The distinctive piece on the left is actually a custom attachment for a 12mm diameter inductive...

I designed this 1kg filament spool holder specifically for PP3DP UP PLUS /PLUS 2 3D Printers, as a response to cheap and wide ABS/PLA filament printing rolls from China manufacturers that proved too heavy. These problematic spools led me to break my...

A replacement set of buttons for the Up Box Plus 3D Printer. It tends to break after extended use and Up Box doesn't sell replacement buttons, only the whole side panel of the printer. ...Best printed flat wit the buttons facing up.

Human: 9/4/15 - Please check out my new rollers upgrade that make a significant improvement over earlier roller bearings:http://www.thingiverse.com/thing:999851 2/11/2015 - Version v2 added with raised bars (+15mm) to prevent extruder motors from...

Here is a brand new mount for your old Raspberry Pi camera holder, now compatible with my beloved Simple Metal PrintrBot Plus. I've tested it on my trusty Model 1504 with heated bed and it works like a charm - although, I must admit that I haven't...

I faced issues with my PrintrBot Plus V2.1 printing very tall objects, where the Z-axis guides wobble led to slightly overlapping sides near the top of the Z-axis. This causes X-axis belt tension to become loose, despite being tight at the bottom. I...

The Shroud is tailored to deliver exceptional airflow for PrintrBot Plus 1404 Dual Extruder enthusiasts. Strategically designed fan mounts seamlessly integrate with 40mm fans for optimal performance. Tightly spaced holes precision-cut to snugly fit...