k1s dash cam 3d models
22858 3d models found related to k1s dash cam.thingiverse
This is the rear mount for the K1S dash cam in a BMW 1 Series Convertible (E88). It clips in on the rear vent and under the roof cover and does not need any adhesive, the just mount your camera on top of it (you will need to invert the camera...
thingiverse
I designed a dash cam support to be mounted on the inside mirror. ... i used the ball joint and the nut from the dash cam parts.
thingiverse
I needed a mount for my dash cam because the suction cup was messing up my windshield tint. I would print this out of PETG or similar due to the heat. PLA+ works but gets very soft. ...I used 3M double sided automotive tape to mount it.
grabcad
This clip allows you to mount a dash cam to the passenger sun visor. You will require an M5 20mm cap head bolt, washer and nyloc nut. The nut in the picture was machined for the purpose, note the camera fitting is tapped M5 so the cap head bolt is...
thingiverse
Link For Dash Cam Kit I Used: https://www.amazon.com/gp/product/B07DGS11CM/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 Link for Mirror Mounting Bracket:...
thingiverse
The dash cam I printed these for uses a Mini USB cable, which is a bit thicker in size than most Micro USB cables. If your dash cam uses Micro USB cabling or any other type that is not the same size as mine, you may want to scale this print down a...
thingiverse
These are meant to sit on your dash and face sideways, to help you see around corners for traffic. The camera mount was designed to fit in the corner of the dash against the windshield of my 2000 s-10. I made these out of abs and have 1 of them...
thingiverse
This bracket is a better design for the SJ1000 Dash Camera that allows you to see the screen through the bracket. Instructions Print with support. ... Remove the Plastic camera holder from the belt...
thingiverse
- Xiaomi Yi Smart Dash Camera mount - Didn't want to remove original mount from my car when I traveled abroad and wanted to use the camera in rented vehicle... ... - Printed in PETG, 236C, 100%infill, 25% fans - Use thick, double sided tape to stick it...
thingiverse
This is a mount for a standard, cheap [yi cam](https://smile.amazon.com/dp/B01CW4ASS0) Simply wedge this up by your rear-view mirror and run a long [usb cable](https://smile.amazon.com/dp/B073PT6Q1P) around your windshield
thingiverse
My holder for the cam broke, printed a replacement mount with petg but the sun melted and deformed the piece. So made this to hold in place even with sun exposure. You have to cut the holder of the original holder. ...Mine was already broken so had no...
prusaprinters
Got tired of the cam constantly falling down as no sticky tape/pad would stick to the plastic cover on the boot lid “roof”.In the end I decided to make a simple mount that hooks on the plastic cover and keeps the camera in place.Printed with PETG to...
thingiverse
Spare 70 mai dash cam mount. ...Mount with two sided tape to windshield.
thingiverse
Automobile Sun Visor mounting clip for the Garmin Dash Cam 45. ...I recommend using the one without the teeth.
thingiverse
My G90 dash cam is great, but the mount that came with the dash cam was really bad. It kept falling of the window. I bought a better one on Ebay for the "Nextbase Dash Cam HD DVR Camera 202 302G 402G or 512G" But to make it fit, I needed this part...
thingiverse
Rove R2-4K Dash Cam Built in WiFi GPS Car Dashboard Camera Recorder with UHD 2160P, 2.4" LCD, 150° Wide Angle, WDR, Night Vision https://www.amazon.com/gp/product/B074JT3698 5V/3A(MAX) AC/DC TO DC Buck Power Converter...
thingiverse
The Lukas Blackbox dash-cams come with a windshield mount. If you loose it you can print your own. Just use VHB tape to mount it on the windshield. ...Be careful with the placement, because it is not adjustable.
thingiverse
So I made an adapter that you can glue to the dash cam and made it stick out 16mm to clear my rear view mirror mount. I prefer my dash cams to be higher up the window for clearance on window shades. This did require me to super glue the mount to the...
thingiverse
This is the Dash Cam Mounted created for my Instructable "Dash Cam for under $20" Note that depending on this design may need to be adjusted depending on the dimensions of the suction cup hook you use. ...
thingiverse
This replaces the suction cup hanger for the Ausdom Dash Cam. Use the original mounting hardware and high quality mounting tape to mount this to your windshield. ...The original suction cup does not stick well to the tinted area at the top of most...
prusaprinters
This replaces the suction cup hanger for the Ausdom Dash Cam. Use the original mounting hardware and high quality mounting tape to mount this to your windshield. ...The original suction cup does not stick well to the tinted area at the top of most...
thingiverse
Compact mount for Nextbase dash cams. Fits my 522GW and probably others if they have the same mount :) Fixed angle of 30 degrees (for my 2005+ Aygo). ... Simply push (or glue) the 2 pieces together and attach to your windscreen with double sided tape.
thingiverse
I wanted to use a Garmin dash cam in my Tacoma, but I wanted to use the stock go pro quick release mount so I made this adapter. Just put the circular base (without magnet) between the two pieces and either screw, melt, or glue each half...
prusaprinters
This mount adapts the stock rearview mirror stalk to some common rearview mirror dash cams available on Amazon under many brands. I can't be 100% sure which ones it will fit. The model/brand I designed it for no longer exists.I installed mine on a...
cults3d
I use my Note 2 to listen to music while I drive, but I wanted to use it as a dash cam as well. It sounded like another perfect opportunity to make a custom mount. Wanting to avoid suction cups that could fall off and to keep it away from the sun, I...