k40 laser head 3d models
164073 3d models found related to k40 laser head.thingiverse
Remix of the K40 Laser head plate from Christoams. ...I found the plate to be a bit flimsy so I added a reinforcement piece.
thingiverse
I bought the "special pro" laser head from LightObject for my K40 conversion (http://www.lightobject.com/Special-Pro-laser-head-mount-for-30mm-mirror-25mm-focus-lens-LR-Type-P787.aspx) and realized that I needed a way to mount it to the stock K40...
thingiverse
Also in the design I included to reference points to use in aiding squaring the laser head with mirror 2. I used a laser level, and a dowel to make sure mine was fine. But if you don't have access to either of those, you can just as easily remove...
thingiverse
It sets atop and around the laser head There are no screws in this design, so no trips to the hardware store. There are two ball joint receivers mounted to the ring for attaching fans, lasers, etc. I have included the files for the fan, laser, drag...
thingiverse
** Required: * screws that match the base of the head * some skill at laser cutter mirror alignment * you may also want to drill out the laser opening at the bottom to 4mm; 2mm is too hard to align. * you may need to measure your existing head mount...
thingiverse
... the back dash with the lens hole and bottom mirror screw to make sure your mirror is perpendicular to the mount. Cloudray Laser Head: https://a.co/d/eg7u9yq Drag Chain: https://www.etsy.com/listing/820150873/k40-40watt-c02-chinese-engraver-laser
thingiverse
This design is for laser cutting. Work in progress. ...Prototype in cardboard and adjust dimensions if needed.
thingiverse
Designed for a K40 laser cutter to adapt the Cloudray head. ... The Cloudray head is 7mm higher than the original K40 head.
thingiverse
Mount to use the Cloudray K-series laser head on my k40 laser cutting machine. Sorry, I didn't set the units correctly. You will need to reduce the stl file needs to 10% when slicing. I sldo included the Fusion360 partfile for remixing. This...
thingiverse
I love this laser head, I always need to change the focal length depending on the material I'm using. So this saves a lot of time. I've bought 2 pieces of line laser (9mm and without focus) It shows the point of the laser where the two lines cross.
thingiverse
I made this laser head holder set for a K40 Laser Engraver/Cutter I recently acquired. It consists of the plate and mirror holder. It makes aligning the 3rd mirror and lens easier. In addition, it has a place to attach a cable chain to run your...
thingiverse
I ordered dual lasers for my K40 Engraver and didn't like the mounts they came with, so I created my own. ...I angled them in such a way, so that if you have a 50.8MM focus point lens, the 2 lines on the laser will meet and form a point at the correct...
thingiverse
This is a Gantry head for the upgraded laser head for the K40 Laser. ...It has a mount for a laser pointer.
thingiverse
used this laser: https://nl.aliexpress.com/item/32796442940.html?spm=a2g0s.9042311.0.0.27424c4depAyEa ----------------- Yes, you're free to leave a small tip if you like this design. Just click the button on the left "Tip Designer" . ...I'll appreciate...
thingiverse
K40 Laser Head Mounting Plate for Adjustable Mount / Head. Short protrusion at the rear so that it doesn't prevent endstop from being hit. ... Bracket with 2 x Diode (12mm) located here: https://www.thingiverse.com/thing:3323420
thingiverse
For 6-7 ID air tube and 12mm OD laser pointer to help with the placement of the work piece.Only m3 screws and you might want to glue the nuts in place.
thingiverse
Hi this is a 3D sliced head interlock design, made to fit the K40 laser bed of 300 x 200, so as slicer for fusion makes the outside line for cutting in blue, all you have to do is change your speed and power level for vector engrave, if your using...
thingiverse
K40 Laser Head Mounting Plate for Adjustable Mount / Head. 2 x 12mm Diode holes - these are exact - so recommend you fit the diodes before mounting the bracket, as you will require force - they will however, not move or require fixing of any kind....
thingiverse
... cutouts for hex head screws and nuts to the bigger clamp. ... There is a small test body for the cutouts. You can change the cutout size in the fusion360 file. It's a parameter. Added a spacer for the mount, to increase the height of the laser tube.
cults3d
... cutouts for hex head screws and nuts to the bigger clamp. ...There is a small test body for the cutouts. You can change the cutout size in the fusion360 file. It's a parameter. Added a spacer for the mount, to increase the height of the laser tube.
thingiverse
This is a mount for on top of laser head to accept a long bolt mount for a drag chain on K40 Laser made from 3mm cast acrylic 14% power, 6-7 ma, 300 mm/sec for Raster Engrave. 16% power, 7-8 ma, 300mm/sec. ...Vector Cut.
thingiverse
The design is mirrored to allow the M3 (i used M4) to sit behind the laser head at 12 o'clock with the air assist nozzle sitting at 3 o'clock, with the 2 laser lines at 4:30 o'clock and 7:30 o'clock. this clears the laser beam path, and gives...
thingiverse
In order to adjust the laser ray properly, the cloudray head had to be closer to the X rail . Once printed, fix the head on the holder. Bold the two parts together, don't tighten it too much, adjust the distance to the rail, then adjust the hight,...
thingiverse
Den Halter vom Cloudray Laser Head hab ich von hier genommen: https://www.thingiverse.com/thing:3061893 Kettenhalter hab ich von hier: https://www.thingiverse.com/thing:3076480 Es kam öfter die frage wie ich den Riemen anbaue: Man nimmt den Winkel...
prusaprinters
Vorher nicht so wirklich. Die Schiene hab ich auf die vorhande X-Achse montiert. Den Halter vom Cloudray Laser Head hab ich von hier genommen: https://www.thingiverse.com/thing:3061893 Kettenhalter hab ich von hier:...
thingiverse
If you want to use the Cloudray K series mirror mounts and D12 laser head in your OMTech K40, then you'll need a new second mirror bracket and laser head mount. First Mirror Install -------------------- You will need to drill holes and use sheet...
thingiverse
I needed a focusing lens adapter to use my stock 12mm focusing lens in the LightObject air assist head.
thingiverse
A usefull bracket for attaching things like cable chains to the k40 laser head.
thingiverse
a merged the k40 laser head mount for Cloudray by zabbazabba and the K40 Drag Chain Kit by dbtoutfit the carriage bracket tall