kallel card shuffler tray 3d models

So, I designed these guides to fit into a standard card shuffler machine. These guides are 69mm wide to keep the cards lined up so they file through the machine appropriately. Designed for cards that are approximately 1.75” x 2.75”. Because of the...

If you have a shuffler like this - https://www.amazon.com/Kangaroo-Shuffler-2-Deck-Blackjack-Cranked/dp/B07PPHB41V - and the handle broke, this is an adapter to fix the issue. Notes: Basically... 1) A hole needs to be drilled through the...

Print the gears with supports and 50% infill (I suggest increasing walls to 5-6 for strength as well). All other parts should print fine with about 20% infill and no supports. ...

This item was created with Customizer on thingiverse.com! Here is the link to customize this object again: https://www.thingiverse.com/apps/customizer/run?thing_id=54395 Using these settings: * The no-angle setting is turned ON * I am not building...

... at 5 mm Bottom height : Adjusted to a thickness of 1.8 mm Resolution (Printer setting) : Optimized for printing at 120 DPI. ... Tray maximum Height: Set no higher than 22 inches Height at the front side : Precisely positioned at 25 inches

A replacement gear for the KiwiCo card shuffler machine (the small-sized gear.)

I made this as a replacement gear for the Nestor Johnson Card Shuffler. ...I intend to hold the knob in place with a small screw and washer at the end.

This is an adapter for the [Card Shuffler Vario](https://www.amazon.de/dp/B000IYTOIC) by A.S.S in order to better shuffle the cards of the [Skip.Bo](https://www.amazon.de/dp/B00006YYY5) game. Since these cards are smaller, they tend to rotate and...

Modified parts for the manual playing card shuffler from user RockstarAlchemist. The goal of this remix was to reduce plastic usage, making the shuffler more efficient. --6-5-17-- A modified crankface and crankface backplate were added, using less...

This is a remix of the "Spielkartenmischer / Card shuffler" by farfadet53. I added a cut-out on the front panel and the card slot so that the cards can be easily removed. You need to print all the other parts from the source at...

... but that might be an artifact of the cards I have on hand or something else being off. A softer material would probably be easier to stretch to fit onto the rollers and might catch the cards better. ...Let me know if it works if you give it a try!

Initial STLs uploaded; photos to come once available. *Note:* the first layer on this will effectively look like a grid, or a bunch of diamonds. If your printer cannot handle small shapes on the first layer, consider printing with a raft. ...(I would...

I Can't Read Or Create Your Message. Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=641938 Instructions Using the following settings: thickness: .4 cornerDiameter: 3 $fn: 60 diameter: 22.5...

A customized version of the Thing at http://www.thingiverse.com/thing:54395 has been created using the Customizer with the following specifications: hole diameter of 2.39mm, no angle of .1, tip height of 4.7mm, cog base width of 1.5mm, cog base...

Customized version of http://www.thingiverse.com/thing:54395 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54395 Instructions Using the following options: hole_diameter = 2.39 no_angle = .1 tip_height = 4.7...

Customized version of http://www.thingiverse.com/thing:54395 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54395

I Designed Custom Bands for the Manual Playing Card Shuffler The rubber bands I had readily available were too bulky for the shuffler to function efficiently, so I designed perfectly proportioned bands in OpenSCAD and printed them with NinjaFlex.

printable bands for the Manual Playing Card Shuffler the rubber bands I had on hand were too thick for the shuffler to work well, so I drew perfectly sized bands in openscad and printed them in NinjaFlex. Print with an 0.4mm nozzle and remember to...

So, I designed these guides to fit into a standard card shuffler machine. These guides are 69mm wide to keep the cards lined up so they file through the machine appropriately. Designed for cards that are approximately 1.75” x 2.75”. Because of the...

card tray

Card Tray for holding playing cards

Customized version of http://www.thingiverse.com/thing:54395 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54395 Instructions Using the following options: no_angle = 1 cog_tip_width = .6 internal_diameter = 36.6...

A personalized version of http://www.thingiverse.com/thing:54395 was crafted using the Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=54395). ...The specifications employed were: no_angle = 1, cog_tip_width = .6, internal_diameter...

Customized version of http://www.thingiverse.com/thing:54395 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54395

Very simple Card Tray. ...8.5 inches long.

Customized version of https://www.thingiverse.com/thing:946475 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=946475

A card tray that fits standard sized cards up to 92 mm. 6 trays fits into a standard board game box. Note that the outer dimensions of a standard box might be consistent but the inner may not. The inner dimensions of a standard game box vary...

These are custom-designed game trays for the bard card game, specifically tailored to hold Dominion cards within a board game box. The trays stack effortlessly for convenient storage. Interlocking features allow multiple orientations to support...

Additionally, it includes sturdy brackets that securely connect multiple trays at their base, ensuring they remain stable and organized throughout play. ...This practical solution is ideal for engaging in complex games like Firefly, which often involve...