kerfmaker 3d models
24 3d models found related to kerfmaker.thingiverse
Kerfmaker (100x20mm version) with some improvements and pocket for magnet (d8x3mm) Hardware: 2x M4x20mm hex cap bolts 2x M4 nuts d8x3mm magnet (optional)
thingiverse
Features of this design 1) This kerfmaker is designed and included with all necessary parts, so no additional metal bolts or nuts are required. 2) If you do not change the direction of the attached STL file, you can print without setting support,...
thingiverse
Based on a few different designs I've seen floating around including the commercially available one from Bay City Tools I printed this at 30% infill and 3 exterior walls and used PLA to avoid the warping since the ends needed to be very square. M4...
thingiverse
The Kerfmaker is a simple adjustable Joint Tool for quick and precise Joints made with the Tablesaw. This one was designed to use a 6mm round head square neck bolt. It is probably possible to use a 1/4" round head square neck bolt. ... To see the...
thingiverse
ccrumpacker's Kerfmaker use M4x20mm bolts, but I only found M5x20mm and M4x16mm bolts at my local hardware stores (Home Depot, Rona,...), so I remix it. ...This version use M5x20mm bolts instead, there is also a M4x16mm version
thingiverse
ccrumpacker's Kerfmaker use M4x20mm bolts, but I only found M5x20mm and M4x16mm bolts at my local hardware stores (Home Depot, Rona,...), so I remix it. ...This version use M4x16mm bolts instead, there is also a M5x20mm version
thingiverse
3D printable kerfmaker for cutting dados on a table saw. See my video below for how to use this jig. ... Required Hardware: 8-32x1/2" flathead machine screw 6-32x1/8" socket cap screw
thingiverse
I had trouble getting a good grip on the thumb screws, so I added more grooves for better grip. I also sized the hex pockets to be a little smaller than the hex bolt head. Just heat up the bolt head with a lighter about 20 seconds and press it in. No...
thingiverse
This is a remix of ccrumpackers version. I printed his and found it to be too large, using too much plastic for my liking. I looked at others and they were all quite large, compared to the real McCoy! I used m4 bolts, but had to trim the ends...
thingiverse
Though these designs are sleek and cleverly constructed, I saw - admittedly a pretty tiny - room for improvement: After the first cut you have to turn the kerfmaker bei 180°, then do the second and subsequent cuts → I chose a design that utilizes a...
thingiverse
This is based off ccrumpacker's Kerfmaker, but I've remodeled it to be able to accommodate a full kerf from a 7/8" dado stack. I also made a few tweaks to tolerances of the sliding components along with improving the knurling and accessibility of the...
thingiverse
A shorter version of the top part to allow making larger dadoes with a regular kerf blade.
cults3d
It is used to create perfect fits from one piece of wood to another with a table saw. On the internet you will find many videos explaining how it works. You will need the following material to assemble it: 2 M4x14 grub screws (the ones without...
thingiverse
Pask Makes designed a tool for perfect datos out of wood and I wanted one in plastic. ... Pask Makes: https://www.youtube.com/watch?v=fNZWlLPw0HI
thingiverse
This is remix of https://www.thingiverse.com/thing:2672696 modified to use 1/4 inch hardware. See https://www.thingiverse.com/thing:2672696 for details of use. ... Requires: Print 1 top, 1 middle, 1 bottom and 2 knobs 2 1/4-20 x 3/4 hex bolts 2...
thingiverse
Big size kerfmaker for perfect grooves. Min 17 mm, Max 100 mm. The idea was found when i saw original Kermaker on bridgecitytools. For assembly you need: - 2 M5 screws; - 2 M5 nuts. Dont change the direction of STL models. ...
thingiverse
... ...Edit it online https://www.tinkercad.com/things/0zc4qOLQvi6 Just designed this for a friend. You'll need to just add your own thumb screws and you are all set. My version of a much more expensive kerfmaker. ...Should do the job just fine though.
thingiverse
... m5's to tighten the kerfblocks together after measuring the stock, and the m3 is adjusted to the kerf of your sawblade. check YouTube for usage (search kerfmaker) I based this design off of a combination of Jay Bates and Pask Makes designs... ...
thingiverse
Klemmanschlag speziell für die Verwendung an der Bosch GTS10XC in Verbinfung mit einem Kerfmaker. So gelingen perfekte Längsschnitte um etwa Aluschienen einzubauen. (Wenn man keine Oberfräse verwenden kann oder will) Zusätzlich gibt es noch...
thingiverse
After publishing the Kerfmaker, Thing:1345031 I had a number of requests for the Tenonmaker so I modified the design and have tested this out. It works well and even had the flip down part that prints as one piece. The top part will need supports. M4...
thingiverse
The setting for the rip fence is done via the wheel (small knob from the kerfmaker of Zeropage: https://www.thingiverse.com/thing:2979838) in the rip fence. For the circle cutting device you have to do the rip fence and turn it over and on again,...
thingiverse
Here is what a kerfmaker is and what it does (skip ahead to the 4:30 mark if you're not interested in seeing this made of wood); https://www.youtube.com/watch?v=YsfOWa_TFR8&t=173s I ordered the knurled low profile thumb nuts from here;...