kershaw lucha parts 3d models
550430 3d models found related to kershaw lucha parts.pinshape
handle inlay for kershaw lucha they just press in place no glue or screws required
pinshape
Handle scale for Kershaw Lucha balisong. ...I recommend that you print it with a rigid material at a high infill.
thingiverse
Handle inlay for the kershaw lucha balisong they simply press fit in place and shouldn't require any kind of adhesive to stay in place. ... to remove them just push them out from the inside of the handle
myminifactory
Sheath for carrying a Kershaw Lucha Balisong in your pocket. Especially useful for latch-deleted Luchas. Takes some time to break-in, there will be some resistance before then, it only takes about a week and a half of consistent use. This is a...
thingiverse
Printed in ABS with 100% infill; holes are for a CIVIVI pocket clip using M2 screws.
thingiverse
This is a work in progress, and my first "complicated" model. It's not 100% accurate and screws are still a work in progress. I haven't printed this myself yet, but I'm fairly certain it's not going to print in place without supports. I included the...
prusaprinters
<p>This is a work in progress, and my first "complicated" model. It's not 100% accurate and screws are still a work in progress. I haven't printed this myself yet, but I'm fairly certain it's not going to print in place without supports. I included...
thingiverse
Remixed to use a pocket clip I had laying around from my benchmade 940. You will need 3 m2 x 3mm heat inserts, and 3 m2 x 6mm screws. If you've never used them before, they're fairly cheap on amazon and all you need to do is press down on them...
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
thingiverse
Customized version of https://www.thingiverse.com/thing:714444 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=714444
thingiverse
Customized version of https://www.thingiverse.com/thing:714444 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=714444
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=693090 Instructions Using the following options: build_lug = 1 small_heart_level = 1.5 big_heart_outline_level = 1.5 alignment = 0 small_heart_outline_level = 2.0 line_space_factor = 1.05...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=693090 Instructions Using the following options: outline_width = 3 build_lug = 1 lug_level = 2.0 small_heart_outline_level = 2.0 text_level = 2.0 text_font = knewave.dxf heart_fringe = 1.0...
thingiverse
Lucha Libre Amigo! ... We appreciate your likes The best regards from México
thingiverse
This is a snap in place backspacer for the Kershaw Grinder. ...The fit is a little snug in the middle.
thingiverse
This is a snap in backspacer for the Kershaw Cryo. ...It can be installed without disassembling the knife.
thingiverse
This is a replacement backspacer for the kershaw Link. ...you will need to disassemble to install this.
thingiverse
This is a friction fit back spacer for the Kershaw Cryo 2. ...It simply pops into place
thingiverse
this is a replacement backspacer for the Kershaw OSO Sweet. ...you will need to disassemble the unit to install.