keymod angled foregrip 3d models

The bracket's angle positions the speaker 5mm from the wall for optimal sound quality. A center hole is drilled for a standard 1/4" diameter machine screw that fits my speakers. I believe this size is common among speakers but I'm not certain. The...

This set of angled brackets is designed to hold your power strip (54mm x 38.5mm EU model) at the edge of your workbench or table for easy access. They fit perfectly with my power strips, but please note that they may not be compatible with yours -...

This is a remix for an angled grip with a steeper angle, and no rests or rails on the side. ...this is a forward angled grip, it is not intended as a vertical foregrip, it even says so on the side.

Rivalburn v3 foregrip remixed to fit TCUB - Extended with RMAX 1

Game ready model of a Daniel Defense 1913 Picatinny Vertical Foregrip.

Game ready model of a Daniel Defense M-LOK Vertical Foregrip.

The Remington Woodsmaster Model 740 is a semi-automatic rifle manufactured by Remington Arms between 1955 and 1959. There are not many aftermarket parts officially noted by remington including a forgrip. I designed a more modern design for...

I wanted to make a sort of cutoff version with the shorter Rival mag. It's surprisingly comfortable, considering most of the actual grip part is missing. ... Category: Mechanical Toys

FX Impact Forgrip ive remixed from various parts. ... print with supports, facing upwards

This remix longer and stronger, than original design. ... You need: 1) M4x30 screw x2 2) M4 nut x2

This is a substitute pin designed specifically for the Masada ACR SPR airsoft rifle. ...I strongly advise using an infill percentage of 30% or higher, and ideally increasing the outer shell count for optimal results.

I really liked the original for many reasons but it just barely didn't fit my KWA TMP9 perfectly, so I modified a brick off of the back rail to provide more comfortable clearance, and then modified the side segments so the folding ambi stock can fold...

I tightened the loose screw so that it fits perfectly now. The print job was completed successfully, and I'm glad it works as expected. ...To make the handle accommodate the design, I reduced its size by about 2-3% to ensure a snug fit.

<p>I modeled the Punisher Skull and added it to the Short 2 IPT file in this source. <a href="https://www.thingiverse.com/thing:580466">https://www.thingiverse.com/thing:580466</a></p> <p>I found this one <a...

Remastered by Maverick (Banshee) and enthusiast Vandal (Maverick's Shadow).

This is my HexCut MOE grip's final edit, perfected through rigorous testing and tweaking. ...I've put in the time to get it just right, and now it's ready for its debut in the world of Airsoft - take a look!

CHANGE NOTE 3/10/19 - Completely redesigned for enhanced strength, comfort, and effortless printing. CHANGE NOTE 1/31/19 - Modified print orientation of Pgrip_2ta. CHANGE NOTE 1/11/19 - Let's achieve maximum thickness. CHANGE NOTE 11/27/18 - Added...

Just fully reworked it and made it even more extensive! ...Split version now available!

You'll require four 20 by three millimeter screws for this project. Additionally, you'll need to smooth out the bottom of the Nemesis by sanding it flat. ...The grip has been secured with epoxy adhesive, but I've decided to further reinforce the bond...

The original design by wolfie1981 had some significant issues on the bottom that made printing challenging due to the balls not sticking properly to the bed, a critical requirement in 3D Printing. Fortunately, the creator released the design under...

Simple Avenger Pump Grip, designed specifically for compatibility with Xero1Tec's high-performance pump rails, was conceptualized and commissioned by innovative engineer Hank. ...This ergonomic grip is now available on Thingiverse at...

This is a remix for the bolt hole that was a little confusing, so made it to fit M5x35 hex screw

For Human Interaction Enhancement

I originally found this [post](https://www.thingiverse.com/thing:3329181) and it was a good start, but kind of a wonky model IMO (no offense). I saw that it was remixed from this [post](https://www.thingiverse.com/thing:3063544) and went to work to...

Took the original design, made it ambidextrous and strategically cut it down to a size that is compatible with my airsoft gun, the Umarex TAC, which is a pistol carbine conversion so having it in a small package was crucial. It attaches to picatinny...

Since I wanted a more flush build, i designed this grip/handstop. It is meant for Tubular m4, or any tubular handguard. ... Feel free to remix it!

Fits perfect on a picatinny rail using three or fewer screws. ... Fasteners used: 10-32 X 1.25 LONG BHSCS 18-8 SS BLACK OXIDE https://www.mcmaster.com/97763A233/ 10-32 NYLOCK NUTS18-8 SS BLACK OXIDE https://www.mcmaster.com/94407A113/

Fits perfect on a picatinny rail using three or fewer screws. ... Fasteners used: 10-32 X 1.25 LONG BHSCS 18-8 SS BLACK OXIDE https://www.mcmaster.com/97763A233/ 10-32 NYLOCK NUTS18-8 SS BLACK OXIDE https://www.mcmaster.com/94407A113/

увидел в игре stalcraft интересный обвес, передняя рукоятка сделанная из обычной рукояти АК, рукоятей на тинге валом, да и у меня от сайги после тюнинга осталась, решил попробовать реализовать. понадобится длинный болт с гайкой для крепления рукояти...