knife and sheath comic 3d models

a little knife for scenery or minis

http://www.ebay.com/itm/Custom-Fire-Damascus-Steel-Drop-Point-Blank-Blade-J620-For-Hunting-Knife-/253057750135?_trksid=p2047675.l2557&ssPageName=STRK%3AMEBIDX%3AIT&nma=true&si=%252FBsP7zF2ryjqsJFfJREY7m8T%252Bb8%253D&orig_cvip=true&rt=nc I remixed...

... sure to cut off the base on the bottom. it is there be cause without it the knife falls over in the middle of the print. Also comes with 1 in handle extension! *JUST RELIZED THAT YOU NEED TO SIZE THE KNIFE DOWN TO 0.6 FOR IT TO FIT IN THE SHEATH

Yet another knife sheath

The model is fully ready for export to the game engine. ...You buy a knife, a sheath, and a leather strap for a knife.

Here's my version of Hunter's Knife and Sheath from the Bad Batch. The knife is split into two parts that just slot into each other. Should be about 12 inches long. ... Be sure to post a make and check out my other models.

I made this knife sheath to fit a 1 3/4 inch belt and a 5 inch knife. ... There's 2 sheaths, one for a multi-tool and another one for a folding knife. Material is TPU of any harness. ...

I made this knife sheath to fit a 1 3/4 inch belt and a 5 inch knife. ... There's 2 sheaths, one for a multi-tool and another one for a folding knife. ... Material is TPU of any harness.

its a knife sheath i designed fo a selfmade knife.

Thin walled Knife sheath to keep sharp knife sharp and fingers intact. Instructions brim of 10mm worked well. ...no support needed

This is a grip and sheath I've designed for the Mora Knife (MoraKniv) blank. The blank (the blade only) was purchased on Amazon for $9. I measured it with calipers and created a CAD file in SpaceClaim. Since I am doing a Boolean cut on the grip, the...

... I sketched its blade with special curvature. However, my first work cannot fit the knife well because of the spherical aberration. The uploaded file is the 2nd version of this knife sheath, they fit perfectly. ...I also add a logo of my workshop.

This Sheath Knife was design in three sizes. ... - 135mm x 38mm - 105mm x 34mm - 75mm x 24mm It support a blade's width between 2mm and 3mm, or maybe more.

A simple sheath for knifes 6.79x 1.89mm Can remix this to change the name to desired name

Knife sheath: simply glue both parts together. The words in Palatinate dialect (part of southern Germany) mean: Danger! Watch out! ...

This knife sheath is for an Ikea knife that didn't have one. It can be printed on the edge without supports. ...I recommend a raft or dots to keep the edges from curling up.

A knife sheath that I designed for a handmade wooden grip knife with a Swedish "Morakniv" blade. The sheath was designed to fit tight enough to not slide of, but still loose enough to easily be removed. Hope you enjoy this print! ...Print Settings...

This Sheath Knife was design in three sizes. 135mm x 38mm 105mm x 34mm 75mm x 24mm It support a blade's width between 2mm and 3mm, or maybe more. Print Settings Printer: kuttercraft Rafts: No Supports: No Resolution: 0.2 Infill: 100% Filament:...

This knife sheath is for an Ikea knife that didn't have one. It can be printed on the edge without supports. I recommend a raft or dots to keep the edges from curling up. Instructions Print on the...

  Designed for transporting a small chef's knife on camping trips. ...The knife blade is approximately 28mm tall, 143mm long, and 1.8mm thick, but it can probably be scaled to fit other knives.

... camping trips. ... The knife blade is approximately 28mm tall, 143mm long, and 1.8mm thick, but it can probably be scaled to fit other knives. ...Printer: -- RigidBot Filaments: (full list can be found on thrinter.com) -- Hatchbox Transparent Black ABS

... trips. ... The knife blade is approximately 28mm tall, 143mm long, and 1.8mm thick, but it can probably be scaled to fit other knives. ... Printer: -- RigidBot Filaments: (full list can be found on thrinter.com) -- Hatchbox Transparent Black ABS

... for a certain length inside, to hold the knife by friction. The part with the long name has both needed parts (in one part), bend and glue. Or print the two other parts (flip the small one for easy print without supports) and glue them together.

... for a certain length inside, to hold the knife by friction. The part with the long name has both needed parts (in one part), bend and glue. Or print the two other parts (flip the small one for easy print without supports) and glue them together.

......Edit it online https://www.tinkercad.com/things/2o40mZjfmAj I needed something for work to keep my knife in so I came with this just push out on the Dot to remove your knife safely. Dot not included. ...:( I updated the file made it a little thicker.

Knife and leather sheath 3D scan

I couldn't find a compact holster for my phone wallet and knife. ... So I made this one. Every Day Carry Sheath for phone, wallet and folding knife.

High Poly Schrade Extreme SCHF3 Survival Knife with nylon Knife Sheath 3D Model. ...BLEND, MA, FBX, OBJ file formats

Combat Knife and Sheath model created with Blender 2.79 Rendered with Cycles principled bsdf shader (PBR) Knife -Faces : 1430 -Verts : 1580 Sheath -Faces : 2157 -Verts : 2352 All PBR textures are 4096 x 4096 -Base Color Map -Height Map -Metallic Map...

Simple pocket sheath for the Bark River Little Creek EDC knife. ...Fits my knife perfectly every time, I have printed it four times already!