kobalt miter saw dust collection 3d models

Used for better duct collection on a Kobal 12" miter saw. Available in shot and long version. Photos are the short version. ... I used double sided sticky tape to attach it to the saw, even though it is a snug fit.

Dust collection for Kobalt 12 inch Miter saw. Uses 4 of the magnets listed below, but honestly friction fits into place perfectly fine without them. There are 2 2-1/2 inch ports, but 1 is honestly sufficient if you're just using a shopvac; if...

Dust collection for Kobalt 12 inch Miter saw. Uses 4 of the magnets listed below, but honestly friction fits into place perfectly fine without them. There are 2 2-1/2 inch ports, but 1 is honestly sufficient if you're just using a shopvac; if...

Adapter for the Kobalt Table Saw to go from the standard port on the bottom to connect to 2" PVC fittings or 2.5" dust collection hose.

Dust Adapter for Hitachi Miter Saw and Kobalt Table Saw to fit a Shopvac hose

Dust Adapter for Hitachi Miter Saw and Kobalt Table Saw to fit a Shopvac hose Category: 3D Printing

This is a Dust Collection Hood that surrounds the saw blade to collect the as much saw dust as possible. I have a small printer so I printed this in pieces and dovetail them together so no glue is necessary. This fits the Bosch GCM12SD Miter saw. ...Im...

I designed this because I was not happy with the OEM dust collection on my Milwaukee Miter Saw, my preference in the shop is to connect my vacuum to it so that I have less cleanup afterward, but the saw came with a rectangular port for some strange...

Adapter to my Tool Shop Miter Saw so I can connect it up to my dust collection. I'm using a Rigid Shop Vac host for the larger end of the adapter. ...Customized version of http://www.thingiverse.com/thing:1246651 ...

This is an adapter to connect a DeWalt DSW780 Miter Saw to a VacMaster Wallmounted 5HP shop vac. ...The bushing sizes are 42mm x 54mm.

This is an adapter for a Metabo miter saw to adapt to a 2" PVC pipe fitting or a 2.5" hose.

This is an adapter for a bigger dust collection hose. ...~60mm or 2.3" hose

- Saw Connector Test Fit: is the end that goes on the saw -- it should slide on with just a little resistance and should twist and lock securely onto the dust port's lugs. - Hose Adapter Test Fit: fits over the 2.5" dust collection hose. This is...

- Saw Connector Test Fit: is the end that goes on the saw -- it should slide on with just a little resistance and should twist and lock securely onto the dust port's lugs. Hose Adapter Test Fit: fits over the 2.5" dust collection hose. This is...

Kobalt miter saw blade guarded bushing part number os1s

I needed a zero tolerance insert for my kobalt 24v miter saw. ...designed in sketchup with .skp included for any modifications.

This fits onto a Bosch sliding compound miter saw and adapts it to standard 2.5" dust collection hose. ... I printed this at 3 perimeter layers which made the model totally solid.

extraction for your miter saw on your large extraction tube

... smaller shop space. Tested on these specific models: Vacuum: https://www.lowes.com/pd/Shop-Vac-12-Gallon-6-HP-Portable-Wet-Dry-Shop-Vacuum/1001435286 Saw: https://www.lowes.com/pd/DEWALT-12-in-15-Amp-Dual-Bevel-Sliding-Compound-Miter-Saw/1000145735

This print will convert the oval dust port to fit over a 1" vacuum hose (1.25" OD on the hose). ...&nbsp;The model was designed using imperial units, so you may have to convert to inches, depending on the slicer you are using.</p><p>&nbsp;</p>

However, I have my miter saw in a dust hood, and just wanted to control the angle the dust exited the existing port, especially at the bottom of the cut. This ensures it goes back into the hood, rather than up at an angle. ... I have a DWS715, which is...

Adapter for connecting a 2" dust collection hose to the Metabo HPT/Hitachi Miter Saw C10FSHC. Drop-in replacement for the OEM dust bag. ...Friction fit.

I have the Kobalt 12" Compound Miter Saw, that tilts both directions. This is the locking handle for the tilt part of the saw. This handle is right next to the handle that locks the miter plate. THIS handle lifts up. The other handle pushes down....

Adapter to connect a pool vacuum hose to the dust port of a Craftsman 20V sliding miter saw.

this is uploaded from the raven https://www.theraven.us/index.php/2020/02/22/dewalt-miter-saw-dust-collection/

Connects a 12" Dewalt miter saw to a 4" dust collection hose. Customized version of https://www.thingiverse.com/thing:2461538 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2461538

My Bosch Compound Miter saw is great, but the dust collection on it leaves a lot of opening. The port doesn't come close enough to the material to catch as much dust as possible. I designed an extender. It fits on the dust port and doesn't interfere...

... ... Scale up the file by 2540% and print with 100% infill. Takes 45 minutes to print in vase mode at 60mm/s Push it in to the miter saw dust port. Very tight fit. ... Also compatible with the riving knife dust port on the 60v max table saw.

Drop in replacement dust boot for the Harbor Freight 12" miter saw not sure about the 10" model, I don't have that one, the laser will still function as normal too, it works rather well, enjoy !

I made this to mount on my MS250 Delta Miter Saw to catch the saw dust coming off of the blade and redirect to the bag or vacuum. 2nd iteration and it fits and works very well. ...There must have been an original plastic piece on the saw but it was...