kobalt tool holder 3d models
413398 3d models found related to kobalt tool holder.thingiverse
This is a first attempt at making a tool holder for the Kobalt Router table. It is printed in two parts to avoid using supports. The pieces will be bonded with glue. This holds two inserts, the 1/2" collet, the starting pin, wrench, and lift allen...
thingiverse
Inspired by the other Kobalt 24v tool holders I set out to make my own. These provide a very good and strong fitment. I added a spacer for the tools that require it. ... The circular saw requires 2 spacers.
thingiverse
This is a tool holder mount for the Kobalt 24v Max line of tools. The tool holder definitely works for the drill, impact driver, and circular saw, and probably others with similiar dimensions. I will be designing further refined versions for the...
thingiverse
I picked up a set of metric and inch T-Handle Kobalt hex wrenches because Home Depot had them on clearance. Great hex wrenches...crappy holder. So...I designed this to sit on my tool table. It holds the hex wrenches. It's got labels for each wrench...
thingiverse
I wanted to hang my Kobalt 24 volt hand tools from the underside of my shelf, so I built these a few months back. The current STL's are my third version, and allow for countersunk screws, no supports required, & prints in just around an hour for each...
thingiverse
This is a little something I whipped up to hang my 24v Kobalt tools from the underside of a bench, or in my case some cabinets.
thingiverse
Designed and printed wall mounts for various Kobalt 24v tools. Reciprocating Saw (requires supports) Oscillating saw and Hand Light Impacts and Impact Driver Skill Saw High Speed Drill Battery Mounts The spacer was designed to evenly space...
thingiverse
1x1 Gridfinity module designed to hold a Kobalt deburring tool. Should work for any deburring tool 17mm in diameter or less. - Holes have been designed to eliminate sagging or the need for supports (stepped holes). ... - Based on the Gridfinity...
cults3d
Made a quick battery holder for my extra Kobalt batteries. ...Enjoy
thingiverse
Designed for my shop as no other battery holders were out there for the Kobalt 24V.
cults3d
This is a battery storage solution for Kobalt's 40v batteries. ...It mounts into drywall with drywall anchors or a stud using wood screws.
thingiverse
The Kobalt 80v trimmer uses a loading method where 6 foot of trimmer line is run through the head, and then bump feed is turned to coil the line inside. The problem is that there's nothing to grab hold of, and as it turns the bump feed will retract...
thingiverse
Needed something to mounts spools overhead on my rack. ...This is for a Kobalt Heavy Duty steel rack you can get from Lowes.
thingiverse
I bought these as a set but they're no longer sold together, so here are the links of the items I designed this for: https://www.lowes.com/pd/Kobalt-72-Teeth-1-4-in-Drive-Quick-Release-Ratchet/1000251049...
cults3d
This print, shown in gray/silver, allows us to use a 40 volt Kobalt (Lowes Home Improvement store house brand) battery with a 40 volt Greenworks tool, but only the tools that carry the batteries externally. My Greenworks blower works and it looks...
thingiverse
This print, shown in gray/silver, allows us to use a 40 volt Kobalt (Lowes Home Improvement store house brand) battery with a 40 volt Greenworks tool, but only the tools that carry the batteries externally. My Greenworks blower works and it looks...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=537516 Instructions Using the following options: holder_cutout_side = 0.0 holder_x_size = 17.5 holder_x_count = 6 wall_thickness = 2 holder_y_size = 50 closed_bottom = 0.0 taper_ratio = 0.9...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=537516 Instructions Using the following options: holder_cutout_side = 0.0 closed_bottom = 0.0 holder_height = 15 holder_offset = 0.0 holder_y_count = 2 holder_x_size = 50 strength_factor = 0.66...
thingiverse
This is an adapter plate to go from 20mm x M4 bolts, to the US standard 1-inch x 1-inch spaced pegboard for the Kobalt 24v Max Tool and Battery Holder, made by [@sgilboy](https://www.thingiverse.com/sgilboy/designs)...
thingiverse
Wall mountable holder for Kobalt 40V batteries. ...Designed to store my many Kobalt batteries up and out of the way by attaching them directly to some 2x4s along my garage walls.
thingiverse
Decided to move Kobalt tool kit to my tool box. This is the design I made for the sockets. ...Posted my design for the wrenches My Other Designs https://www.thingiverse.com/search?q=rac552&page=1&type=things&sort=relevant
thingiverse
Decided to move Kobalt tool kit to my tool box. This is the design I made for the sockets. ...Posted my design for the wrenches My Other Designs https://www.thingiverse.com/search?q=rac552&page=1&type=things&sort=relevant
thingiverse
Decided to move Kobalt tool kit to my tool box. This is the design I made for the sockets. ...Posted my design for the wrenches My Other Designs https://www.thingiverse.com/search?q=rac552&page=1&type=things&sort=relevant
thingiverse
Just a couple simple parts that snap into the area between the handle and the box on my rolling Kobalt tool chest. Makes use of some wasted space since I rarely move it. ... One fits 3 average sized drivers and the other is for 2 larger ones.
thingiverse
I designed a bit holder that attaches where the belt clip mounts to. It holds two 1/4" screw bits. You will need an M4x10mm Hex Button Head Cap Screw. It should be a button head to make sure it doesn't stick up too much around the edge of the...
prusaprinters
... 0.4<br/> Gradual Support Infill Steps: 2<br/> Gradual Support Infill Step Height: 3<br/> Enable Support Interface: (unchecked - disabled)</p> <p>Update: I recommend 100% infill. 20% infill is too weak. Category: Tool Holders & Boxes
thingiverse
I designed this tool holder to keep the driver set together. I've owned several of these set but can't ever find them when I need them. And so it was born. This thing was made with Tinkercad. ...Edit it online...