kobra max firmware 3d models

Just a simple filament guide to avoid tangles. Print with 100% infill for maximum strength but its not necessary. Used zigzag supports for the clip part only. Hole lines up directly over where the filament feeds into the extruder. ... The whole part...

A simple table handle. Fixing with superglue or plastic solvent. ...

Damit das Filament nicht immer auf das Gestell des Druckers tropft. ...

I build for myself because I couldn't find the right one for me. I am sharing with you.You need about 1.5 m of LED strip. ...:) easy to remove if you are fixing something.You need to print part1, part2 and holder twice, use super glue.

Customized version of https://www.thingiverse.com/thing:749887 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=749887

Customized version of https://www.thingiverse.com/thing:749887 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=749887

Customized version of https://www.thingiverse.com/thing:749887 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=749887

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/9sOGN4d0q1U

The VORTEX red dot sight is a rapid acquisition sight for M4A1 weapon systems such as the M16A2, M4A3 and CAR-15 series rifles. The VORTEX sight has 18 brightness settings for the green dot allowing the soldier to be able to engage targets in night...

This is my design to fit 120 mm fans and 25 mm thick fans of the motherboard and PSU. Just mirror the model if want the single model. I also prepared a 4 feet ready to print. ...Just rotate the feet of the front so that it will fit.

The trash bin was right on. I found a model on thingiverse, but there is a different fixation of the tray. Printing PETG from Eryone with a tray printer. ...240/75 In the grooves of the profile, the tray occurs with an interference fit, just so...

I made this PRIZM fan duct for the powerfull blowing of the printing model. It uses two 5015T 24V fans. I use fans from "Usongshine" brand. This fans begin work normally in low blowing mode from 70% and till maximum at 100%. May be other fan brends...

Remix on “Squash Feet (longer)” by Popcorn To use new “Cover Plate for PSU” (https://www.thingiverse.com/thing:5990917) and “Cover Plate for Mainboard” (https://www.thingiverse.com/thing:5990907), you'll need these Feet to lift your 3d printer...

I designed this on TinkerCad. ...You can make remixes of it and adjust it as you like.

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

Hier ein Cover für das Netzteil ohne die Schutzstreben vor dem Lüfter um den Geräuschpegel zu reduzieren.

I had to replace 2 printhead cables due to stresses at the connector. I designed this to slide on to minimize the flexing at the printhead. V2 has a wider slot, as the replacement cables and newer units are thicker as they are using more tape. ...Can be...

Remix of "Raspberry Pi Camera Holder for Anycubic Kobra by Dosimo": https://www.thingiverse.com/thing:5805884 - changed the holder to fit the Kobra 2 - increased hole size to 3.1 mm to fit a 3mm screw - front file is unchanged

Please use my Vyper-specific mount located at this link: https://www.thingiverse.com/thing:6360400 >This mount should work on Anycubic's Kobra Plus and Kobra Max models that use the same printhead assembly as shown in the pictures. It also has a...

This is meant to replace the display on the Kobra Neo with a mounted phone, since the stock display isn't compatible with Klipper. ...Print as oriented, shouldn't require supports.

I adapted it to the standart Anycubic Kobra Neo print surface by changing the color, changing placement of the writing and adjusting the writing. ...I also modified the 3d model.

A purely mechanical hack to auto power off the Kobra 2. At the end of a print, the printer moves the build plate forward, pushing a lever arm that flips off the power rocker switch. ...

I made it slighty smaller, with some addons like, led stip holder remixed withhttps://www.printables.com/pl/model/709480-anycubic-kobra-2-pro-led-top/filesand fiment guide hole. ...Feel free to download

It features the use of the stock screws of the original Kobra filament holder, the possibility to use JUSH in full width (even two spools on top of the Kobra possible e.g. for quick filament change) and filament guide holes to the extruder which...

When you have only few or no space next to your printer, this is my solution for you.It features the use of the stock screws of the original Kobra filament holder, the possibility to use JUSH in full width (even two spools on top of the Kobra...

MOTU Action Figure Kobra Khan Camouflaged Toy Tops Vintage. Approximate Size: 7" Figure is sectioned for printing. Includes a sample of my master, with this file it is indicated that it is my own digitization. ... Any questions I am at your service.

---- Ein Einfache Display-Abdeckung für ein Anycubic 4,3 Zoll Display (entworfen für ein Kobra Plus) Es sollte bei mir in erster Linie Nachts das leuchtende Display abdunkeln. ... Es dient aber auch als einfacher Schutz um versehentliche eingaben am...

... "feet"), it should snap into place on the rail and will even slide a bit so you can adjust the position. I believe this will work for both Anycubic Kobra Neo AND Go printers, and theoretically any printer with rails matching the above measurements.