kobra max firmware 3d models

Die Abdeckung kann auch für das Netzteil des Anycubic Kobra Neo verwendet werden. Es wird jedoch ein anderer Abstandshalter an den Füßen benötigt: https://www.thingiverse.com/thing:5894002 *** Remix of the Air slots. Over the contact rail, the...

... to make it with the 2020 Reverso Context. There is a connector for you as well. I printed it with Kobra 2, it could be connected with the reverso context very tight without any bolts. ...But you still be able to make it tighter with some M3 bolts.

This scrap box fits for Anycubic Kobra 2 (not Neo Version) as well.I liked the model very much so I decided to make it a little bit smaller (120 mm instead of 160 mm) to have a scrap box for the right sight, where the display is located, as well.The...

... tags using Z-Offsets from 0.25 to 0.4mm. ... Variations for different nozzle sizes and perhaps temperatures to come. Printer: Anycubic Kobra Plus Filiment: PLA Layer Height: 0.3mm First Layer Temp: 210 Other layer Temp: 200 Bed Temp: 60 Nozzle: 0.60mm

This is a remix from the original to house the skr mini e3 v3 motherboard and fit on an anycubic kobra. ... parts needed 4 m3x25 bolts 4 m3 lock nuts 4 m3x12 bolts 4 m3 t-nuts printed or purchased 3 m3x10 bolts reuse original 4 bolts...

This is remixed (very badly) to fit the Kobra Neo. I'm not a 3D modeler so I did what I could.Seems to work better than stock. ... Supports are only needed for the unsupported ends of the ducts, and if your printer is bad at bridging you might want to...

This is my created Anchor for the Anycubic Kobra side filament system. https://www.thingiverse.com/thing:5633816 I use two M3 screws an nuts. Customized version of https://www.thingiverse.com/thing:5139044 Created with Customizer!

Really rare cause nearly nobody uses the AC Kobra with the Sonic Pad.You can use the delivered screws from the Sonic Pad and mount it onto the right side ot the printer head. Printed with 0,6 nozzle and 15% infill.

new part cooling fan duct for Anycubic Kobra WIPif using CURA Resolution .15mmprint speed 803 wallsinfill 20%3 bottoms layers3 top layersinfill line multiplier 2

Improved version of the USB Holder for anycubic Kobra 2 Neo that I created.Added 4 holes for microSD cards.Fully compatible with the grips of the first version, in case you already printed it, you only have to print the central part.

made for anycubic Kobra 2. Just made the upper filament holder (another cool stuff) and put it on the top of the printer. Then the filament hangs down and nearly kinked before it moves in printer. ... So i made this thing to guide the filament...

new part cooling fan duct for Anycubic Kobra WIPif using CURA Resolution .15mmprint speed 803 wallsinfill 20%3 bottoms layers3 top layersinfill line multiplier 2

Made with Tinkercad.GER: Ganz simple Füße für den Anycubic Kobra 2 Pro. Gedruckt aus TPU werden die Vibrationen des Druckers etwas gedämpft. Die Füße passen genau auf die bereits am Drucker vorhanden Füße und halten dort von Alleine. In der Mitte...

... can use the Fusion 360 files as well Important! ... To use this cover, you need to have “Anycubic Kobra Squash Feet” (https://www.thingiverse.com/thing:5990893) or other new feet to lift your 3d printer You'll need: - 4x M3x26 mm Screws - 4x M3 Hex Nut

Anycubic Kobra neo/2 neo filament tube holderI designed this to fit with a upper spool setup (like this one) and to prevent the filament from bending hard on the left side (with the original tube location) and still using the tube that comes with the...

Anycubic Kobra 3 Camera LED Quick FixUntil they sort out the LED issue in the Kobra 3 camera, here's a handy workaround for you:I've tweaked the original back-plate of the camera case so you can attach a small LED light to it. It's designed to work...

This is a rotatable Anycubic Kobra Neo holder-type 2.It is difficult to make a bearing balls with Kobra neo, so I decided to buy balls. 6 Φ8 balls are used to make one bearing. Since we need 2 bearings, we need 12 balls. Φ8 balls are beads without...

This is a heavy remix of Anycubic Kobra Neo Z-Axis Camera Mount - Updated by Vap3Lif3_MCMXCV.I wanted a stable mount I could easily add or remove without removing screws and potentially throwing off the x-gantry alignment. This remixed mount is...

... can use the Fusion 360 files as well Important! ... To use this cover, you need to have “Anycubic Kobra Squash Feet” (https://www.thingiverse.com/thing:5990893) or other new feet to lift your 3d printer You'll need: - 4x M3x10 mm Screws - 4x M3 Hex Nut

A Top-Mount Spool Upright Bracket, designed explicitly for the AnyCubic Kobra Plus and the Dual spool system by 00monster00. https://www.thingiverse.com/thing:4174482 The model has an enhanced base that has been reinforced for increased...

This tool box and trash bin connects to the spool holder on the Anycubic Kobra Neo 2. I assume it will connect to other models as well that have a 1 inch circular hole in the spool holder arm. ... The perfect hardware would be 25mm M4 bolts, but just...

I did not have space to fit the Anycubic Kobra Filament holder above the printer so removed the bracket, took off the spool holder and designed this to be screwed into a wall to hold the filament. ... I then printed one of the many filament holders...

The thing that I based this off of (https://www.thingiverse.com/thing:5866977), doesn't have any provision for the little control board in the Kobra's hotend carriage. I lack the skills to relocate all the electronics, so I modified this file to...

Here is a simple and effective, adjustable Z axis belt tensioner for the Anycubic Kobra 2.This is an adjustable variant of my original Kobra 2 belt tensioners, found here - https://www.thingiverse.com/thing:6306407...Designed to fit in with the...

Needed a bracket to convert my Anycubic Kobra Plus from the trash stock mainboard to a BigTreeTech SKR E3 Mini v3. You will also need an 8010 fan for a bit more clearance, otherwise the fan will hit the power connectors of the mainboard. And then the...

Original posting: This is a remix of combination of Vap3Lif3_MCMXCV fan duct that was designed using https://www.printables.com/model/378928-anycubic-kobra-neo-fan-duct by Martin. ...The circular fan duct was found on the internet (no idea where I got...

Beim Anycubic Kobra befinden sich am Netzteil ungenutzte 24V Anschlussklemmen. An die wird der Step-Down-Regler angeschlossen und dann auf 12V eingestellt. Die Abdeckung muss auf Grund der Druckbettgröße in zwei Teilen gedruckt und anschließend...

Tried some other Z axis camera mounts for the Kobra Neo and found them to shake and wobble with high speeds and accelerations. So I designed a more rigid mount that seems to perform quite well. There is still some wobble, which could be fixed with a...

UPDATE (16/08/2024) : Taking advantage of a few free days I have updated this thing a little, adding a second removable support, slots for MSD cards and USB in addition to adding a support for the TEFLON Tube, I have re-designed two versions, one...

Rotated Spool Holder of Anycubic Kobra 2 (Pro) I was inspired by the original and like the original I decided to make it for lateral attachment because I think that the weight of spool made more stability to the printer at high speed if is attacched...