lack table enclosure 3d models

...Then, they are joined together to form one larger table with two extra legs left over to extend from a third lack table and fit your printer underneath. I'm confident I explained it well enough. Soon, I'll be sharing photos of the finished product.

I recently got the MMU2 for my Prusa MK3 and needed to route 5 ptfe tubes from the mmu unit to above my Ikea Lack enclosure. This is my simple attempt at doing so. It just requires 2 M3 screws per tube. The tube hole may require some effort to get...

I stumbled upon the E3D Nozzle holder and have been utilizing it for a few months until I constructed my LACK enclosure. I needed something to hold my nozzles and preferably position it near or next to the enclosure. So, I imported the STL into...

 Just need a few screws to mount these to the legs of your Ikea Lack enclosure.I think I printed these (.4 nozzle) .2 layer height with 20% infill double wall. ... Could print them a little beefier, but have had 4-5 spools on it and have had...

This remix draws inspiration from the innovative enclosures found on https://www.thingiverse.com/thing:2864118 Update: A critical addition was made to prevent the enclosure doors from swinging freely when the top is removed. Larger handles were also...

I created a custom version of the Ikea Lack leg extensions, giving them an extra boost in height to accommodate my Anycubic i3 Mega 3D printer, which stands slightly taller than the Prusa Mk3. ...I chose to print these modified extensions with a sleek...

Small filament guide / gromet to suit the IKEA Lack table. Printed using PLA Dimension: Small guide 12mm wide (10mm insert) 52mm long (50mm insert) Large guide 24mm wide (20mm insert) 52mm long (50mm insert) Installation method: ...

Rigidity bar with handle for Plexiglas door The model was made for my printer setup, two table Lack Ikea is a door height of 80 cm (see photo) You will need 6 bolt screws ⌀3mm per door The file is 73 cm in total and can be printed in 3 times. The...

The standard height of an Ikea LACK table is 400 mm from the ground to the bottom, making it a very snug fit for most Prusa style printers. Adding feet or dampeners to the printer only makes it even harder to squeeze in. I designed this extension...

Hangs underneath your Ikea Lack table printer stand, Requires two skateboard bearings and an 8mm threaded rod to function properly. I use it with these: https://www.thingiverse.com/thing:1998669 and a whole bunch of locking nuts. - The main...

This is a Guide to the Filament Path for the Popular Ikea Lack Table. It features a tube within its inner section, designed specifically for filament, and two additional "half"-tubes intended for cables that support the bowden extruder mounted atop...

I'm designing a modular system to store my 3D printer and accessories within a stack of Ikea Lack Tables (https://www.thingiverse.com/thing:2880834). Since no existing design met my requirements for a robust hidden hinge, I created one myself. This...

https://www.thingiverse.com/thing:2119747 I find that the ikea lack tables are nice, cheap and elegant looking but unfortunately they're constructed by screwing the leg directly into the table top. Over time the legs tend to become loose and will...

...The CCW one is only needed for retrofitting an existing one (so you don't have to re-print a leg extension as well!\r\n\r\n------\r\nSmall remix of thebeetleuk's amazing design.\r\n\r\nHonestly, I've been struggling to build a Lack enclosure myself.

... of hte holder, the newer is with better bottom), on the other hand the .stl is upside down, relative to .gcode. ...The screw hole is 4mm wide.  For now the holder isn't mounted, but I will update it as soon as I am done with building the ENCLOSURE.

I made this Bajonet like Lock for my Ender 3 Enclosure Its important to enable Tree support touching buildplate only I printed this with a 0.2 resolution After Printing you need to clean the Rim for better fitting I hope you enjoy it

Yet another brilliant Raspberry Pi camera holder solution has emerged, making it easier to capture stunning moments without the hassle of a cumbersome enclosure. ... This ingenious design takes its cue from the talented creator behind...

Wanted a filter because fillament came a little bit too dusty, i already had a fillament guide that required drilling the top of my enclosure (link in remix source) so i just added a base that molds around that guide. Havent Printed it, yet. ... -...

... of hte holder, the newer is with better bottom), on the other hand the .stl is upside down, relative to .gcode. ...The screw hole is 4mm wide.  For now the holder isn't mounted, but I will update it as soon as I am done with building the ENCLOSURE.

Phone Holder to run Octo4A in an enclosure. Turn your old android phone into an Octopi server and watch your prints. ...The STL's are designed for a Pixel 4 and the default MacBook USB C Hub, but you can go into Fusion 360 and change the parameters to...

... Prusa Printer's Spool Holder is a mismatch for Hatchbox Spools. ...However, if you stick with the standard spindles and wheels that came with your printer, along with the existing enclosure frame, everything should fall into place seamlessly for you.

A sleek solution to route a USB cable (or numerous others) through the enclosure's gap. Two versatile caps are included - one with a single hole and the other with two, catering to your specific needs. ... The tabletop must be precision-cut into a...

... passthrough connectors featuring M10 threads. **Reminder:** The provided files are optimized to utilize the MMU's color-printing capabilities. Due to a lack of clearance, it's highly improbable that the numbers will fit if printed independently.

This IKIA design secures the MMU using existing hardware and bolts directly onto the enclosure's top surface. To make this setup work, users will need to extend both power and signal wires. Prusa has established a maximum feed length limit for...

I bought a LED strip for my enclosure which I couldn't bent in normal orientation with the LEDs facing down.  So I created a mount for a vertical orientation. You need one small screw to fasten the mount and a zip-tie to fasten the LED-strip to the...

I created this feeder to supply filament to a printer positioned below another one within an enclosure. Inspired by the Prusa spool holder, it allows for easy feeding from underneath. This design is still in development as I've only recently designed...

here is my concept for a ender 3 enclosure legs printed at 20% infill glass clips are for 1/8inch plexi glass at 10% infill I printed 4 legs at a time and it handled it just fine. also I printed 5 clips per side panel. just search hinges and a...

This adaptation was specifically crafted for an LCD enclosure project, which can be found on Thingiverse under the reference number 3464254. The new hinge operates on friction, requiring a gentle tap to secure it in place. ...To guarantee optimal...

It seems to make a significant difference in the enclosure air temperature for PLA prints (with the doors closed, just to see what happens, increased 32C sustained to 36C sustained) so I look forward to trying with ABS where I have more familiarity...

This modification has made a significant difference in the enclosure air temperature for PLA prints with doors closed - increased by 32C sustained to 36C sustained. I'm eager to try ABS prints where I have more familiarity with air temperature...