lack v2 enclosure 3d models

Designed for a 9mm hole, to fit 50mm thick Lack table. Printed without supports or brim. ...Used variable layer tool to make threads .1mm and shaft .25mm for speed/quality.&nbsp;</p>

The modified version of the Prusa/Ikea Lack cabinet door handles utilizes 12mm diameter x 3mm thickness magnets, which can be effortlessly obtained from Amazon, providing a more accessible alternative to the magnets originally specified in the Prusa...

Allows up to 60mm clearance for sound dampening inside the enclosure. Has a huge affect on the noise level of printing. ... I used scrap drywall witch was 13mm thick, have added alternate sizes for different material sizes.

This adapter makes it easy to convert an inexpensive Ikea side table into a high-quality enclosure for your 3D printers, allowing you to control the temperature environment when printing with materials like ABS. Printing out four of these adapters is...

This is a camera mount for any Logitech/Logi camera that can be mounted on top of a monitor. ...I have a C525 but I assume at least some of the other Logitech webcams will fit. It screws into the side of an Ikea Lack table leg.

When using an already built Ikea Lack table the legs are screwed into the top. A 2" wood screw will be too small for the already tapped hole. ...These supports will screw into the leg and the table top with the 3d printed connector in the middle.

I'm creating a custom enclosure for my pet tarantula and designing a unique door handle from scratch. ...The hole is perfectly drilled, 15mm deep, with precise measurements tailored specifically for an M4 bolt that will effortlessly thread its way into...

Allows up to 60mm clearance for sound dampening inside the enclosure. ...Has a huge affect on the noise level of printing.</p> <p>I used scrap drywall witch was 13mm thick, have added alternate sizes for different material sizes.</p> <h3>Print...

My acryl plates are a bit smaller than the enclosure. These are sealings to reduce the gap between legs and acryl. Printed from PETG, no supports needed. ...Full Material.</p><p>You need 2 pieces to fit one side of the acryl.</p><ul><li>5mm variant -...

There are already numerous enclosure designs available that cater to various needs, but none of them met my specific requirement: creating stackable enclosures where no element must be placed above or below another. To achieve this, I had to design...

For this build, I used 2 Ikea Lack tables with the legs on one cut down to give 28" of top to bottom clearance. The windows are 11"x14" thin glass panels from Dollar Store picture frames. The white panels are 5mm thick Elmer's foamboards 20" x 30" ...

For this build, I used 2 Ikea Lack tables with the legs on one cut down to give 28" of top to bottom clearance. The windows are 11"x14" thin glass panels from Dollar Store picture frames. The white panels are 5mm thick Elmer's foamboards 20" x 30" ...

After numerous ideas about the IKEA shelf LACK, I sat down and created some parts myself. These are corners for top and bottom that allow using a plexiglass pane up to 5mm thick. The lower corners are 10mm high in the standard version and 15mm high...

 For any questions about parametrics, and how to add/edit values, check out Prusa's blog post on the subject: https://blog.prusa3d.com/parametric-modeling-in-fusion360_37411/Requests:If you don't feel comfortable with Fusion 360, and exporting your...

The problem arose because another printer was positioned above it, making it impossible to place the spool on top of the enclosure. To resolve this issue, I created a custom hanging spool holder that mounts behind the printer, allowing me to switch...

You can now mix and match the large and small pieces as needed, depending on your clearance between the top of the printer frame and your enclosure ceiling. The mini version includes two different sized nuts, a 12mm nut and a 14mm nut. I designed...

I designed the printer mount to sit atop my enclosure, giving me more space to work with. I chose petg for the print material and set the 3D model to extrude three solid perimeters for added stability. Perhaps I overestimated the structural integrity...

I built a custom enclosure for my printer that allowed me to neatly route the PSU cables underneath the table. The PSU cords were too short, so I had to drill a 25mm hole in the table's bottom to run them through. ...I then placed the cable management...

This is my version for 3D printers enclosure. The height is enough to fit ZARIBO 220 MK3S or Prusa MK3S. There is also filament cleaner on top inside the table, just cut and put the foam inside. Double sided tape is used to put locks on the glass.

I'm still actively working on refining my enclosure design, but most of the elements I've uploaded so far are ready for use. Some of my colleagues and friends appreciate the design and want to 3D print it, which is why I've decided to publish this...

... this matters much. ...Didn't add much to print time or filament usage.Drilling the holeUse a 16mm drill bit to drill through the top of the Lack table.A 15mm will work just fine as well, you'll just have to force screw the top piece through the panel.

This is a project based on the Ikea LACK as a starting point. I designed some components, modified others, and the end result is straightforward to both print and assemble. ... Things to purchase: 50 cm x 50 cm Polystyrene panels (I used 2.6mm...

When I made an enclosure for my Prusa Mk4 printer, I needed something to hold the PSU. So, I came up with an adapter that I attached to one of the table legs. The adapter is modular, so you can choose where to attach it. ...Also, it does not depent on...

... a diameter of 6mm. * Eighteen screws that are 20mm long with a diameter of 4mm. A Fusion 360 project file is included for modification purposes. Next, I will be working on creating a Duet Wifi enclosure to relocate all the electronics outside.

**Enclosure Design**: Review your enclosure design carefully to ensure it's well-suited for the project's components and any future upgrades or changes. 6. **Power Supply**: Verify that the 10A 120W power supply can handle the total power consumption...

I modified the magnetic handles and base for Dominik Císař's Prusa enclosure (https://www.thingiverse.com/thing:2864118) as well as JesusFreke's redesigned handles (https://www.thingiverse.com/thing:2922505). I discovered that using 1/2" x 1/16"...

If you enjoy tinkering with your machine, lifting the top up offers plenty of room to modify rods without removing the printer from the enclosure. This case utilizes standard 50cm x 50cm acrylic panels - two 2mm thick ones for the back and two 4mm...

These washers will hold neo magnets against the plexiglass sides, allowing for easy removal of the enclosure. I printed these legs using Proto Pasta HTPLA with a 50% infill rate. Given the material's excellent layer adhesion and strength at higher...

Minimalistic enclosure built with 50cm x 50cm x 2mm hobby glass panes made of polystyrene. The side and back panes simply slide into place. The front pane slides in at the bottom and clicks securely into position at the top. Taping the edges of...

The Tush with the lock for the Lack case. Print one of the part here and 3 of the originals from here: https://www.thingiverse.com/thing:2047554 One part of the spool holder then locks into place with the lock of the case:...