lara croft 3d model

* The Cura version used for this print of mine is version 4.10.0 Printer model: Ender 3 V2 Filament: eSun PLA+ Filament Color: Fire Engine Red Layer Height: 0.2mm Initial Layer Height: 0.2mm Line Width: 0.4mm Wall Thickness: 0.8mm (Light use) OR Wall...

I need thosethree measurements from that photo: Front standoff spacing, back standoff spacing, and front-to-back spacing.I've already helped several people from across the globe and I've been updating this document with the new models as I go.Post...

It can support itself and needs a lot more force to be bended. If you still want to print your own loc line, I used the models from MinyMan644 found here -> Loc-Line Fittings (1/4", 1/2" and 3/4"). I strongly recommend buying loc line instead of...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.3...

the tabs are at different positions on each model. * Group Token Holder - slots in behind the main card holder. * Player Holder - holds the large Agent Pawns. * Player Tray Base x 4 - print these in the 4 player colors. * Player Tray Top x 4 -...

The source of the model has several parameters that you may wish to change. The current settings are for a silicone tube with an internal diameter of about 4 mm. You can adjust the pen length and width to your preference. Note that some tweaking may...

Description ==================== The display is mostly based on Modeller's 1/64 Initial D display box but I have expanded and slightly upscale the width of the roads to fit Hot Wheels better. The holes for tying the cars are designed to fit most...

This model currently comes in 4 variations. Standard rail facing forward. Standard rail angled 5 degrees to the side off the rail. Standard rail with sidekicks facing forward. Standard rail with sidekicks angled 5 degrees to the side off the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

The parts I used: * 30mm M3 flat screws: https://smile.amazon.com/gp/product/B07NWL5HK3 * 16mm M3 hex screws: https://smile.amazon.com/gp/product/B014OO5KQG * M3 nylon lock nuts: https://smile.amazon.com/gp/product/B07GNXDQJZ * 20mm CR-10 springs:...

My printer is a I3 Pro Dual Extruder, so I know for sure it fits that model and probably all of the I3s that were made with that frame. Update 1/22/18: I added a new mounting plate that moves the stepper motor forward. This allows the X carriage to...

1x set of speakers from MacBook Pro model number A1226, A1211 or A1260. 3W Bluetooth amplifier module TE657 This module goes by many names, so compare pictures when you're unsure.ebay.com / banggood.com / google LiPo charger module TE585 a.k.a...

He shipped back a huge quantity of Parian marble to use for his ethnographic portraits of Greeks, especially for portraits of the peoples of Paros, and eventually realizing at least twenty-seven busts, medallions and full scale figures representing...

As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the platform, using a belt to drive the capstan. I would...

https://www.youtube.com/watch?v=Nn9B46IjsVU ______________________________________________________ ENGLISH ______________________________________________________ Only tested on T12-X, but can work on equivalent models with boxes of the same...

Make the adjustments, render the desired  STLs and print it! The models are in the position, they should be printed. No support is needed. ...I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this...

(You may be able to get away with shorter bolts but these were the only ones I had that would fit) I have included a thumb screw model to make it easier to open and close the cover without a wrench. You will need an M3 heat insert but I cannot stress...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Details and models may change as I continually improve it. Please see the pictures for individual printing instructions. If the spur gear for the table binds when rotating the table, loosen the stepper bolts, push the stepper inwards, and tighten....

This sword model is a more realistic redesign of the Master Sword from The Legend Of Zelda game series. The text on the front of the blade translated from Hylian says, "The Sword of the Hero of Legend" and on the back, "The Blade of Evil's Bane." ...

And for many builders I consider this simpler than going the path of printing Flex material.  Model DetailsPulley and Bearing Press ToolThere is not much to say. It shows the pulley with a bearing and heat-shrink tube on the outside. The third...

Please note the Modular Assembly Preview STL is just to show a preview of one assembly model, not for printing. Here's a brief description of the types of parts included. Cuffs - Number is the inside diameter of the cuff. Diameters include...

For any other question, please feel free to reach out, or leave a comment. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2mm Infill: 20% Filament: Jarees PETG Matte Black Notes: Support is only...

... Included is a PDF with the sizes of all the models. The PDF will also show you the print settings I used to print. There is also a Cura Profile file you can import to Cura to see what settings I used. ... I used a Creality CR10 V3 to do the prints.

Print Settings Printer: Heavily modded Craftbot Rafts: No Supports: Yes Resolution: 0,15 or 0,20 mm Infill: 33 or 50 % Notes: Print both models in PETG with 3 mm thick walls and slightly hotter than usual, this should give you enough strength for a...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

Link below --- Build history Years ago, duno, I made the bigger first case desgin, roughly modeled after the original. 2021 -the 2.nd design of a modified, more streamlined versatile case was made. -modified the pcb layout -new pcb was made...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 42 custom_bottom_fillet_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...