lead bender 3d models
22983 3d models found related to lead bender.thingiverse
Yet another parametric lead bender. An improvement on the one by @onebytegone. ... I have printed and used this successfully.
thingiverse
...... Leads can be formed in 0.050 inch intervals from 1.5 inches wide to 0.4 inches wide. Component bodies can be up to 0.5 inches large on 1.5 to 0.65 inch width bends. Component bodies can be up to 0.4 inches large on 0.6 to 0.55 inch width bends.
thingiverse
A resistor Lead bender for getting resistors bent to the correct dimension. ...Sizes range from 0.4" to 1.5"
thingiverse
Just another component lead bender toll, because the ones I found here and elsewhere were a little bit off, so the bended leads did not fit readily in place. ... Sizes: 25,4mm down to 7,62mm in 2,54mm steps
thingiverse
This is a remix of a component lead bender. The height of the tool is optimized to give the right lead length for solderless breadboards. Several holes at 0.1" spacing were added to help with bending and cutting components with parallel leads. STEP...
thingiverse
This came about when I recently saw Erik's lead bending tool ( http://www.thingiverse.com/thing:6699 ), saw that he didn't have a version with different widths, and remembered a post on Evil Mad Scientist Laboratories (...
thingiverse
I removed these files from Thingiverse because I don't agree with Stratasys/Makerbot and because there's a better alternative.You can find them on their new home: YouMagine!https://www.youmagine.com/designs/lead-bender-tool 3D printers are...
thingiverse
Component lead spacer/bender, 0.1" to 1.0". I was exploring the Thingiverse, looking for a jig small enough for 1/8 W resistors, diodes, jumpers and that sort of thing when this Imperial Star Destroyer materialized in our quadrant. On my desk to...
youmagine
I'm still working on that :)This is a parametric (OpenSCAD!) lead bender tool. It's very simple, but it works for me. I've also included a wider version that can be used to bend an entire strip. Currently it's set to the spacing on the PCB I'm...
thingiverse
I tried laser processing to make it easy to get the accuracy of bending. The square hole was hard to use, so I increased it. The 2222.SVG file can be used for engraving. The step of resistance can be secured by repeating about five times. ... It...
thingiverse
Lead Bender and PCB Gauge. Measure the length on the circuit board, you can bend the resistor. I'm sorry file name was incorrect. It is 100 times the number of the file name is correct. ...Print Settings Printer: BS01 ...
thingiverse
The place that I work does a lot of hand-made circuit boards, and bending 30+ resistors with a conventional resistor lead bender was very time consuming. ...This tool will bend 10 resistors at once to either 0.6" or 0.7" Print Settings Printer Brand: ...
thingiverse
Bender for lead(electronic work) Please secure to breadboard with jumper pins. ... --- more small https://www.thingiverse.com/thing:5266471
thingiverse
Bender for jumper(electronic work) Please secure to breadboard with jumper pins, DIY keyboard making!
myminifactory
Simply place the points of the caliper in the two holes in to which you are going to install your component, place the part in the middle of the gap on top and bend the leads around the edges. For extra precision you can install a screw in the hole...
thingiverse
Simply place the points of the caliper in the two holes in to which you are going to install your component, place the part in the middle of the gap on top and bend the leads around the edges. For extra precision you can install a screw in the hole...
cults3d
Simply place the points of the caliper in the two holes in to which you are going to install your component, place the part in the middle of the gap on top and bend the leads around the edges. For extra precision you can install a screw in the hole...
prusaprinters
Simply place the points of the caliper in the two holes in to which you are going to install your component, place the part in the middle of the gap on top and bend the leads around the edges. For extra precision you can install a screw in the hole...
pinshape
Simply place the points of the caliper in the two holes in to which you are going to install your component, place the part in the middle of the gap on top and bend the leads around the edges. For extra precision you can install a screw in the hole...
thingiverse
If you use Veroboard (stripboard) for electronic prototyping or circuit building you will have experienced the challenge of getting the leads of the components bent just right. This simple tool helps make it simple. Designed for 2.54mm stripboard, it...
thingiverse
This is a simple tool that let you easily bend the leads of a resistor in a "U" shape, you can bend it in three different sizes 0.5in, 0.6in and 0.7in. It was made in 4 pieces, and one spring that i found in an old printer (it wasn't printed, i...
thingiverse
... the pins with the fingers on either side. I will be developing a version for wider chips in the near future. Cura Time: 1hr 30min Material: 4.41m/~13g [UPDATE] Now uploaded, Large DIP IC Lead Bender v1.00: https://www.thingiverse.com/thing:3124978
thingiverse
... a pin bender for the larger types of DIP ICs. ...It is a development of my Small DIP IC Lead Bender: https://www.thingiverse.com/thing:3121797 The pair together should be able to cope with most DIP chips. ... Time: 1hr 52min Material: 6.93m PLA ~21g
thingiverse
... Time (Cura File): 1hr 16min Material: 3.73m/~11g [UPDATE] Please see the version able to deal with longer chips at: https://www.thingiverse.com/thing:3121797 and now uploaded, Large DIP IC Lead Bender v1.00: https://www.thingiverse.com/thing:3124978
thingiverse
https://www.thingiverse.com/thing:4896590 was absolutely brilliant, but the default component was far too large for standard breadboard components, and the implementation would not allow for easy manipulation of the important geometry in the...
prusaprinters
combination of the origiinal diode bender and the lead bending jig :-)
thingiverse
Every line has a standard size, each slot is .05″ longer than the next and has radiused edges to make perfect bends without stressing the leads. It can be used to bend the leads of 1/2 watt resistors, 1/4 watt resistors, and diodes. Esta pieza es...