let's split case 3d models
869724 3d models found related to let's split case.thingiverse
It is confirmed to fit the Let's Split Eh and Let's Split V2. Otherwise it hasn't been tested with other variants. The case requires m3 heat inserts from here: https://www.mcmaster.com/94180A331 And uses m3x16 screws. The top portion is printed...
thingiverse
This is a case for the Let's Split keyboard. I originally had an acrylic sandwich case(116mm x 86mm) and wanted to reuse it for this case. So if you have an acrylic case and want something enclosed, you wont need to desolder switches to use this. The...
cults3d
This is a case for the Let's Split keyboard. I originally had an acrylic sandwich case(116mm x 86mm) and wanted to reuse it for this case. So if you have an acrylic case and want something enclosed, you wont need to desolder switches to use this. The...
thingiverse
... from Aliexpress You may have to sand the holes to put standoffs in (depending on your printer). Build log [here](https://imgur.com/gallery/hHR1U "imgur"). Another version of Let's split case https://www.thingiverse.com/thing:2626039/apps/#apps
thingiverse
These are end inserts for [Smashing Acrylics Let's Split Case](https://smashingacrylics.co.uk/product/lets-split-acrylic-cases/) to close off the individual cases and make everything a bit neater. STLs for both the right as well as the left side are...
thingiverse
I designed this case for the keyboard kit found here: https://keeb.io/products/levinson-lets-split-w-led-backlight?variant=6600662679582 It uses 7x m3 screws on each half to hold the top plate on as well as 4x m3 screws to hold the pcb to the inside...
thingiverse
I designed a lid to be used with [this](https://www.thingiverse.com/thing:2482218) case for the Let's Split keyboard. It is a friction fit on the case and protects the keys/switches in transport. It has a shelf to only allow the lid to go on so far...
thingiverse
I snagged a couple of [these cases](https://stratakb.com/store/cases/lets-split-standard-cases) but being the miser I am spent 2 hours creating a middle skirt piece rather than buy the full case. This was one of my first projects with fusion 360 and...
thingiverse
This design uses 8 x 2.5m 5.6mm threaded inserts, and 8 x 2.5m 10mm bolts.
thingiverse
Absolutely loved the original version, but it didn't engage the retention clips on the bottom of a keyswitch, making it very easy to pop the switch out when trying to change a keycap. ...I remixed it so the plate is the proper thickness around the clips...
thingiverse
I really liked this Let's split case but noticed an issue with the MCU port alignments being too high on the bottom. I have remixed the case to move the ports down in order to make room for the new Elite C v4 which is mid mount and requires lower...
thingiverse
Instead of having [separate tenting](https://www.thingiverse.com/thing:2748628), I incorporated tenting directly into the let's split case, which makes it a lot more sturdy (if not only because there's a ton of material down there). feels a bit...
thingiverse
Sides or "middle layer" for the JOlimon acrylic case I bought with my let's split eh?
thingiverse
This is a 3D print file of the case for Let ‘s Split. ... To secure the case, use M2 screws (thickness = 2mm x length = 6mm) and insert nuts (M2 length: 3mm).
thingiverse
This is a plate & case I built for a "Let's Split" keyboard. In the photos I used translucent filament. ... PCB's will eventually be restocked here: http://www.switchtop.com I use these screws: M3 x 0.5 mm Thread, 6 mm...
youmagine
This is a case I designed for the "Let's Split v2" keyboard that was designed by /u/Wootpatoot on Reddit.https://www.reddit.com/r/MechanicalKeyboards/comments/4p1b02/gblets_split_update_2/ After numerous design changes and test prints, I have come up...
thingiverse
Build log is here: https://imgur.com/gallery/CQ07J You will need: 8x 8mm rubber feets 8x M2 4mm-6mm screws and 2x Let's Split PCB's 48x diodes 48x switches (Supports both Cherry MX and Alps/Matias switches) 2x Pro Micros + spacers 2x TRRS jacks 1...
cults3d
Remix for the Let's Split Keyboard angled case (https://www.thingiverse.com/thing:2626039) and the Remixed to fit switch retention tabs (https://www.thingiverse.com/thing:2895402) remix. Now with 4 5x3 round magnets on the inside to join the two...
thingiverse
Remix for the [Let's Split Keyboard angled case](https://www.thingiverse.com/thing:2626039) and the [Remixed to fit switch retention tabs](https://www.thingiverse.com/thing:2895402) remix. Now with 4 5x3 round magnets on the inside to join the two...
thingiverse
... from the original, with a beveled edge on both halves for the microcontroller. ...fits with pins clipped just fine Edit: I also just uploaded a plate with slightly larger (by 1%) switch holes, in case anyone was having issues with them being too small
thingiverse
... height and spacing around keys V2.5 Changelog: - Changed plate thickness of MX slots to 1.4 from .75. Should make switches more snug. V3 Changelog: - Changed plate thickness of MX slots to 1.55 to match what is used on other plate style cases.
thingiverse
This remix adds in support for a 2u spacebar + smaller posts so the Levinson PCB actually fits.
thingiverse
I got a Let's Split Keyboard PCB and I really wanted a case that was not plate mount, so I designed a case that snaps into the PCB. I'm working on improving print-ability without supports, works decently right now with minor hiccups. Future...
thingiverse
The original version didn't engage the retention clips on the bottom of a keyswitch, making it very easy to pop the switch out when trying to change a keycap. ...I remixed it so the plate is the proper thickness around the clips so they now engage,...
thingiverse
This is a Let's Split keyboard case with Cherry MX switch mounts and Lego compatible legs (16x11). It has been 3D printed and needs to be assembled. The ultimate goal is combining this with a base plate and lego wrist rests to use it on top of...
cults3d
I designed this tenting for this case: https://www.thingiverse.com/thing:2748621 but it should work for almost any Let's Split case, and really any split keyboard that fits nicely in a square shape (so ergodox is probably a no). The angle...
thingiverse
I designed this tenting for this case: https://www.thingiverse.com/thing:2748621 but it should work for almost any Let's Split case, and really any split keyboard that fits nicely in a square shape (so ergodox is probably a no). The angle...
thingiverse
A simple keyboard carrying caddy for my Let's Split keyboard. The board's connectors are fragile and the key tops get caught in the bag all the time. This box protects it from the damage. It may also work as a stand to tent the board - the halves...
thingiverse
Should fit the standard Let's Split / Nyquist plates (and obviously Viterbi--also, it isn't imbalanced). I'm still learning Fusion 360 so I decided to make my own tenting setup. I was running into the issue that at higher angles, a lot more...
thingiverse
lets split case modeled after the TADA68 case. ...work in progress, havent printed yet.