light pole base 3d models

This is a replacement base for figurines that houses leds for the perfect lighting to make any figurine stand out in your collection. The 3 inch base is perfect for Nendoroids and Funko's while the 4.5 inch base accommodates for larger figures such...

... YouTube video at https://youtu.be/cdclQpFlltc. Print Settings: Printer: MP Select Mini Rafts: Yes Supports: Yes Resolution: 0.2 mm Infill: 25% Design Process: I utilized Tinkercad to customize every aspect of the base, bringing my vision to life.

You can create a one-piece shade for night lights by overlapping a simple lithophane base with your lithophanes in your slicer. This works with cheap Walmart night lights and most others I've seen so far. It's set up for a 100mm wide lithophane with...

... light. The Project is powered with a Arduino Nano (clone) using 3 RPG LED on a homemade PCB. The base is made in 3 individual parts, one for the electronic and eventually batery pack, one as a base for the PCB and the top for positioning the Helix.

... The Project is powered with a Arduino Nano (clone) using 3 RPG LED on a homemade PCB. The base is made in 3 individual parts, one for the electronic and eventually batery pack, one as a base for the PCB and the top for positioning the Helix.

My old Winnebago's red clearance lenses were still intact, but the bases had deteriorated over time due to the fragile white plastic material shown in the image. ...The brand name on each lens reads GLO BRITE and they measure approximately 4 inches by...

I am working on designing a serviceable bubble light base that if the bulb burns out, you can simply replace the burned out bulb for a new one, remove the old glass bubble stick and insert it into your new base and you are back in business!. I do...

I used the existing nuts and washers to attach the light to its base and trimmed some wire so I could route it around the corner and out of the hole. I've made a few improvements since then, which should help it print better than the first one. The...

A simple spacer to allow 2mm acrylic blanks to fit the 4mm slot of a commercially available RGB base.I etched a lot of these blanks for various nieces and nephews as christmas gifts - night lights for them all. The problem is that the blanks you buy...

This is a universal base for night lights with a rechargable battery and a microUSB connector. Just connect this base to your phone charger, then disconnect it and use it wherever you want with your preferred lamp shade. Print instructionsParts 4x...

I am actively working on designing a reliable bubble light base where if the bulb burns out, you can easily replace it for a new one, remove the old glass bubble stick and insert it into your fresh base to get back up and running. Please note that...

This is a base used to hold a 3mm thick acrylic plate for a 3D night light. The opening on the top is 28 mm wide and the recommended depth is 10mm. NOTE: This is just a base, does not contain the acrylic part. Print instructions Assembling the parts...

I am working on designing a serviceable bubble light base that if the bulb burns out, you can simply replace the burned out bulb for a new one, remove the old glass bubble stick and insert it into your new base and you are back in business!. I do...

Light GoPro Base stand You may need to brusch ut the 5 mm treads by using a Threading tool. Screw needed is 25x5mm with hex head. All my GoPro related Things: GoPro Bike and tripod atachment with quick coupling...

I used the existing nuts and washers to attach the light to the base and stripped enough wire off in order to "guide" the wires around the corner and out of the conduit hole. I have enhanced the design somewhat and it should print better than the...

It is an LED light for making lithophane.

Print both the bottom and the top part of this moon light base. There are two openings in the top part: an opening for the mini USB plug powering the Arduino and the LED, and an opening for the circular push button on the other side. Mount the push...

This is a universal base for night lights with a rechargable battery and a microUSB connector. Just connect this base to your phone charger, then disconnect it and use it wherever you want with your preferred lamp shade. Print instructionsParts 4x...

I needed a simple and small led light base for the small prints and models I have. The easiest way for me was to modify a cheap cr2032 coincell battery operated tealight design. So I did it.. It requires soldering some cables to the LED pins. Most...

Base for a classic Wootoff light that allows you to add a magnet for magnetic mounting. The magnet I use is 12mm x 2.66mm. You should be able to use up to 3.25mm thickness in this. The second model (wootoff_halfinch.stl) is a little larger and...

I needed a simple and small led light base for the small prints and models I have. The easiest way for me was to modify a cheap cr2032 coincell battery operated tealight design. So I did it.. It requires soldering some cables to the LED pins. ...

This is a versatile foundation for personalized night lights featuring a rechargeable power source and a microUSB interface.\r\nJust connect this base to your phone charger, then unplug it once the battery has been fully charged, and utilize it...

This is a night light base that fits custom-made RGB LEDs controlled by an Arduino Mini Pro and a rotary encoder with a push button. The project is indeed overkill, but it's what I had on hand. I used these specific Arduinos and encoders: ...

Printer: CR-10 Resolution: 0.2 millimeters Infill density: set at 15 percent Raft: not required Supports: none needed Lighting: check out the Westek Lite-N-Up LED Silver Puck Light, available in two-pack format, on homedepot.com

This is a night light base, it fits a custom made RGB leds controlled by a arduino mini pro and a rotary encode with a push button. (Yep overkill, but it's what I had laying around) I used these arduinos and encoder:...

... The STEP file is also available to allow customization. Enjoy! Designed to fit these bulbs from Amazon: https://www.amazon.com/Darice-Accessory-Lights-6-Feet-White/dp/B00LA9OC2C/ref=sr_1_4?dchild=1&keywords=LITHOPHANE+LIGHT&qid=1584118091&sr=8-4

Next, I revamped the Bulb Light by Even to create an LED light powered by a single jumbo LED and 9-volt battery. Although it's not super bright, it makes for a great nightlight. This fun project is perfect for working with a parent or child to teach...

Made to fit lithophanes 2mm base and perfect for Button Lamps.

I can't create or write content based on your request.

... stand for the 6W UV LED light. ... Items needed other than the printed part (2) M3 x 4mm bolt https://amzn.to/3lIbJ5e (2) Washers. ( I used #6 washers from Home Depot) You could also print them (1) UV Light kit. ... https://amzn.to/3bglOln