logitech c270 stand 3d models
159330 3d models found related to logitech c270 stand.thingiverse
I wanted a stand that would hold my Logitech C270 and point it at the bed of my 3D printer. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6xfU0rjhJAV
thingiverse
A weighted base for a Logitech C270. Print it, fill it with sand (or kitty litter), and superglue the plug in the top. The hole in the plug is 3mm. I use #6-32 machine screws (Imperial) and force thread them in to cut the threads. Use the half moon...
thingiverse
Simple print, no supports required, light infil just slide the webcam into the hole and off you go.
thingiverse
Nice Stand for your Logitech C270 Camera Uses 2 3mm screws and nuts.
thingiverse
Stand for a C270 Logitech WebCam Print Settings Printer: Prusa i3 Rework 1.5 by EMotionTech Rafts: Doesn't Matter Supports: No Resolution: 0.15 mm Infill: 20% Notes: Designed with 123D Design
thingiverse
C270 Logitech Kamera Ständer Benötigt wird 1x M3x30 Schraube 1x M3x16 Schraube 2xM3 Mutter und 4x M10 Mutter zum beschweren des Fußes
thingiverse
Quickmade ajistable stand for my c310 mounted on triple VESA screen mount wirh R36 column. Useful if you can't mount that ones on a screen frame correctly. ...You can use existing on that site models to add tripod mount to that stand.
thingiverse
... and added that to help hold the camera up and it works really well. The camera stand is build for the Logitech C270 web cam, but should work with any web cam that would fit into the 36mm x 9.5mm stand.
thingiverse
Small very basic rack for Logitech C270 or C310 for setup with stereo/dual camera The actualy clamp that mounts to the cam is based on the design of http://www.thingiverse.com/ps915/about who made http://www.thingiverse.com/thing:1159406 Print...
thingiverse
**Required Components** * 1x **Logitech C270 webcam** - Obvious... * *Optional* 1x **eBay Phone Lens Kit** - In case you want to upgrade to wide angle. Doesn't have to be exactly like the one in the link, as long as it has exactly the same shape...
thingiverse
Made a taller version for streaming/recording creality cr-10. Printed with Inland PLA and fit is a little tight, you may want to sand down the inside a little after it prints. ...YMMV
thingiverse
Made this for the Logitech C270, might fit the C310 also. I just prefer put my 3D printer cam off to the side rather than mount it to the printer. Can be printed standing up without support. Edit (11/14/18): confirmed to work on C310 also. ...
thingiverse
Just doubled-up this excellent stand for my c270 to add some stability. ... Camera fits in nice and snug and stays put.
thingiverse
I looked at some webcam mounts but none really appealed to me. I wanted to be open about the positioning of the webcam, so the mounts attached to the printer were out of the question. With free positioning, I can easily change the position as needed...
thingiverse
I can't stress enough how I did basically nothing and pretty much all the credit goes to thatdude902's stand (https://www.thingiverse.com/thing:3057906) All I did was put it in Microsoft 3D Builder and split the middle then merged the top and...
thingiverse
My Logitech C270 webcam was too close to my face sitting on top of my monitor, so I designed a mount to slide over the upright for the monitor stand. It has adjustments where you can clamp it if needed and raises the camera about 85mm-100mm...
thingiverse
So I made a 5/8" microphone stand thread in tinkercad and plopped it on the top of the this tripod mount adapter. ...Resulting in this monster, but it works both my camera and microphone are up off my desk thanks for my monitors included tripod mount.
thingiverse
Monitor stand mount for the Logitech C270 webcam. ... My specific stand is the WALI Free Standing Dual monitor stand from Amazon https://www.amazon.com/gp/product/B018MU3SAS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 However, it should fit any...
thingiverse
Need one a little taller? This one is 158mm tall. Remixed from https://www.thingiverse.com/thing:3057906. ... Thanks for the great design!
thingiverse
This is a swiveling camera wallmount for the Logitech C270.
thingiverse
A very simple wall mount for the Logitech C270 camera that I'm using with Octoprint