logitech c920 tripod mount 3d models

I'm struggling to get anything but the initial picture to display ***\r\n\r\nI created this adapter specifically for mounting my c920 Logitech camera on my CR-10's with the supporting rods because I wasn't satisfied with the existing...

This is a Simple print in place camera mount for the Logitech C920 to be used on the y Axis pulley rail under build plate camera screw used is from User AxxAxx https://www.thingiverse.com/thing:578514 screw works great no issues so far. this is just...

Support for holding Logitech C920 webcam, remixed so that it can be fixed on the enclosing cabinet wall. Prints in place, requires an M3x40 screw to fix the two moving parts. Distance between fixing holes is 25mm, fit for an IKEA Platsa cabinet. ...

There are lots of brackets for the Logitech C920 webcam, yet I couldn't find one to satisfy my requirements - so I designed this :) In these modern times of video calls, I needed the webcam to be easily removable and retain its original folding...

I needed a mount for the C920 and liked the other design, however the C920 base is a little wider. Factory screws hold this in place, although I did notice a slight spread apart where it attaches to the printer. ... Just added a new version, more...

This is an easy-to-print camera mount for a Logitech C920 (may work for other camera models with the same bolt size) so it can be mounted from the front of an Ender 3 Pro. The camera screw was remixed from https://www.thingiverse.com/thing:578514...

A bed-mounted webcam mount for the Logitech C920 camera on the Wanhao Duplicator i3 Plus allows objects to be stationary in frame when doing timelapses. This mount requires loosening of the bed by a few millimeters in order to get mounted, but it...

So, are you in the extremely specific situation where you have a triple-monitor mount with an exposed post and have no spot to put your Logitech C920? Well have I got an extremely specific solution for you!Print instructions:I designed this mount to...

This is an easy to print camera mount for a Logitech C920 (may work for other camera models that have the same bolt size) so it can be mounted from the front of an Ender 3 Pro. PLEASE READ THE PRINT INSTRUCTIONS (SEE BELOW) The camera screw was...

The thread insert on the Logitech C920 that allows it to mount to tripods and other standard webcam mounts that use the standard 1/4-20 threading can sometimes fall out.This is a simple replacement if your C920 has a missing thread insert. ...It's sized...

For mounting i used 3M VHB Tape You need: 3M VHB or some screw to mount 2x M3 Self Lock nut 1xM3x15mm (or longer) 2x M3x11mm (or longer) Please upload a photo of your make. This design is not for commercial use or selling! Unterstützte meine Arbeit...

However, it's not a good fit for my C920 cameras, and there's an enormous mount attached that gets in the way. First, remove the hinge from the camera. Then, the base camera mount will fit into the camera housing, allowing you to adjust the camera...

Meant to be a part of the Universal Camera Mount by RaffoSan: https://www.thingiverse.com/thing:2477180 The mount itself is directly taken from Catchy's design (the photo is also Catchy's): https://www.thingiverse.com/thing:2542192 I remixed the two...

The Logitech C920's printed circuit board features precise mounting holes and speaker positioning, along with a somewhat subpar decal overlay depicting the circuitry layout.

I upgraded my camera for my Mendel90 (Octoprint). For mounting i used 3M VHB Tape You need: 3M VHB or some screw to mount 2x M3 Self Lock nut 1xM3x15mm (or longer) 2x M3x11mm (or longer) Please upload a photo of your make. This design is not for...

Logitech C920 Holder for yyh1002's Modular Mounting System. Disassemble your Logitech C920 using YouTube's step-by-step guide at https://www.youtube.com/watch?v=q0wWCd5nmfU. Replace the original mounting system with our custom 3D printed holder.

I removed the C920 case from the printer because it was too bulky inside, but the bed mount still allows access to the front bed adjustment nut and clamps firmly in place below the heated bed. You can print two or more finger joints depending on the...

This is a remix of @JanLorenzen_1372689 https://www.printables.com/model/689977 for the Logitech 920 Web Cam https://amzn.eu/d/fbqlSN0The reason this is a Remix is that it is the part that Jan's model is designed for that is just so slightly smaller...

... to better fit the MK3 and MK3S. The part has also been stiffened up. Mount screw included. Print instructionsFilament: Prusament ASA - Prusa Orange Layer Height: .20 - Quality Infill: 40% Supports: From bed only Picture attached of bed position

This is an upgraded MK2 model, engineered with a tailored mounting arm and top design to seamlessly integrate with the MK3 and MK3S. Additionally, the component's structural integrity has been significantly enhanced through reinforcement. ...A secure...

Originally made for Prusa i3, mk3, mk3s but added support block which allow this mount to be mounted on Ender's 3 Y axis belt tensioner. Disclaimer: Original model for Prusa printers is not my design. ... Author's profile:...

This is a simple stand for a Logitech C920 PRO HD Webcam (PN: 860-000565). ...

You'll need: * High-quality adhesive like 3M VHB or screw mounts for stability * 2 x M3 Self Locking nuts for optimal grip * 1 x M3x15mm (or longer) fastener for reinforcement * 2 x M3x11mm (or longer) rods for additional support Please share a...

I've made the distance from the mount to the sensor according to the C mount specifications (Not CS mount, see update below) so it should in theory work with those lenses, however I don't have such a lens to try it with. I did try with a C mount to...

This is just the adapter to make the G920/G930 camera work with the mounting arm by RJay (https://www.prusaprinters.org/prints/31047-mounting-bracket-for-playstation-eye-camera).This adapter keeps the hinge functionality of the original hinges for...

This mount perfectly fits my PowerSpec 3D Pro. Given that it's supposed to be a near exact copy of the Flashforge Creator X and Makerbot Replicator 2, I'm confident it will also fit these machines, though I'm not absolutely sure. ... Check out my first...

After attempting a few prints of the simple camera mount i kept having the same problem with the outer braces that clamped onto the Y axis snapping. Instead of printing this in 100% infill i opted to increase the width and size of the outer supports...

I've made the distance from the mount to the sensor according to the C mount specifications (Not CS mount, see update below) so it should in theory work with those lenses, however I don't have such a lens to try it with. I did try with a C mount to...

I was looking for a simple solution to fix my Logitech C920 on my BROR IKEA. ... It works perfectly!!!

A simple but very helpful gooseneck mount for the Logitech C920. The Cam can then be mounted onto the CamHolder element. The gooseneck is designed so that the camera USB cable can be fed through the opening. ... You have to print one CamHolder,...