logitech g502 charging dock 3d models
45394 3d models found related to logitech g502 charging dock.prusaprinters
I created this model because i did not want to have to have a micro USB cable just for charging my mouse, most other stuff i have is USB-C For the dock, you would need the following items:A USB cable (any old type A cable should work)4 M3x6...
thingiverse
G502 Charging Stand w/ logitech gaming logo Original design of gmartin314
thingiverse
A flat charging dock for Logitech mouse. Stick the removable round piece that comes with the mouse to the dock. Drill two holes accordingly, then solder the wires to the two magnets. Make sure the positive is on the right, and the negative is on...
thingiverse
Tools required: A USB cable A Logitech mouse with the weight at the bottom After doing some testing I found that the wireless charging mouse pad work by using the 2 magnets on the bottom as + and -. So I simply connected the + and - of a USB cable...
thingiverse
New pinkie rest for Logitech G502. This new model replaces the original back plate with this one. There is a hole to introduce a M3 nut so the plate is magnetic. ...Fits awesome, like if it were official from Logitech.
thingiverse
... against the force of the splint for it to connect. will update if needed. Oh and here is the Reddit page where we talk about that this issue. https://www.reddit.com/r/logitech/comments/thh6po/logitech_g502_keeps_disconnecting_and_reconnecting/
myminifactory
This is an alternative to the one given by logitech, it weigh about 0.6 gram (at 100% infill) which allow for more precise weight distribution.
thingiverse
Charging stand for Logitech G502 Lightspeed, should work with other powerplay compatible mice. I found the USB cable on my G502 a bit awkward, the port is too recessed and it's tricky to remove without pressing buttons. So I designed a charging...
thingiverse
I currently haven't printed this, however i have printed the version its remixed from Filled in the holes, and moved it so that it can take 2 small screws which should stick to the mouse's built in magnets and will also act as the charging contacts...
cults3d
I currently haven't printed this, however i have printed the version its remixed from Filled in the holes, and moved it so that it can take 2 small screws which should stick to the mouse's built in magnets and will also act as the charging contacts...
thingiverse
This is a very simple charging dock to be used with Logitech MX Master 2 wireless mouse. You can simply slide your mouse into the charging position, when you do not need it. You will have to check, if your usb cable looks the same as on the picture....
thingiverse
I made a lid so that I could add weight to the support and also cover the hole
thingiverse
Made this for my Logitech G502 mouse, pretty sure it works for others as well! ... Cord Length of G502: 6ft.
thingiverse
This remix extends taller to help support the Crayon better while charging. This is meant for a classroom use. It is just my first stab at it, and I haven't printed it yet. ... Stay tuned.
thingiverse
Hello guys, This is a stand/storage for Logitech G502 gaming mouse I have made. ... If you make one, share a picture with us!
thingiverse
Here is a Stand for your Logitech G502 Wireless...have fun
thingiverse
I have the nice stand from [Mansdask](https://www.thingiverse.com/Mansdask/about) for two years now, but I often found myself not using it, because it is inconvenient to plug the mouse in. This changes now! This remix enables you to simply...
thingiverse
This is a rocket chaging dock for the Logitech Crayon stylus for iPad, inspired by the Apple Pencil Rocket Charging dock (https://www.thingiverse.com/thing:1478052). I've designed it from scratch for a bigger, more stable base, a more gradual turn...
thingiverse
Link to headset:...
thingiverse
Logitech g502 hero custom bottom plate. Since I have large hands, I decided to make a custom bottom plate with thumb rest for my g502 mouse. Original is attached with magnet, but this one can be glued on with duble sided tape. I have other designs...
thingiverse
A remix from anikiandy's model Link: https://www.thingiverse.com/thing:4505651 I enlarged the micro usb entry, two tunnels were made to be able to pass the cable and plug in the mouse to charge it while it remains in the dock A space was made at the...
thingiverse
... so that it doesn't need a magnet to keep the baseplate in place. Thus bulk of the work was done on my previous model for the G502 Lightspeed for the pinky rest portion and I just merged it with the updated baseplate model and updated thumb rest.
thingiverse
I needed a charging dock for my iPhone 12 Pro and my Apple Watch. I just came from Samsung and I had a PG9201 wireless charger that I had been using and wanted to keep using it. It charges the phone just fine. This combo is kind of unique so I need...
thingiverse
I use this cable: http://www.ebay.com/itm/For-Samsung-Galaxy-S3-S4-Original-USB-Data-Charging-Cable-Cord-Sync-Charger-ONE-/371241268045?var=&hash=item566fb4334d:m:mitgD51FiWyXsA29ER4RfJw Print Settings Printer Brand: 3D Systems Printer: Cube 3 Rafts:...
grabcad
... charger(5,5S,6,6PLUS). -Can be used as an inductive charger. -Indicators(indicates that power is low or high). -Speakers(indicates on getting fully charged). -Can be used anywhere. -Easy to handle. ...-Meets CARUS Designs(3mm rounded at corners).
cults3d
I based my design on HeraSk work.(https://www.blendswap.com/user/heraSK) I included the original .blend file. The print is about 2h long, depending on the speed you choose. ...I included in the file only the mouse cage: you have to design the stand by...
thingiverse
I based my design on HeraSk work.(https://www.blendswap.com/user/heraSK) I included the original .blend file. The print is about 2h long, depending on the speed you choose. I included in the file only the mouse cage: you have to design the stand...
prusaprinters
<p>You need:<br>4x M3 brass thread inserts<br>4x M3x10 countersunk screws, holes are deeper and longer screws can also be used</p><p>Printed mine in XPETG by extrudr.<br>0,15mm layer height for mount, 0,2mm layer height for...
thingiverse
Pretty much did it as @wildflight did it. I just branded it a bit :) and customized it inside based on my needs. Thanks lots @wildflight for this project. ...Really appreciate it ;) I did not find the inserts for M3 screws so I just used plain M3...