low profile clamps 3d models

V1 of my low profile clamp idea. ...Working on V2 as a single piece.

This is a low profile, adjustable clamp. Do not print this, it is a project for metal. I have made mine in steel. ...Use 6mm hex bolts.

This is a low profile clamp which is especially useful if your CNC is equipped with a dust shoe. It exists in two sizes: 80mm and 110mm. The width of the slot in the middle is 5.4mm (ideal for use with M5 screws - e.g. ...X Carve).

Low profile clamps for PCB milling on 3mm sacrificial plate. On a Stepcraft D model use M6 nuts, and M6 countersunk screws with 12mm length and conical head. ...

This ia a low profile clamp. Its design is very commonly seen on the internets, but the drawings and other details are always behind a paywall. This annoyed me, so I made my own and publish the design. I made them in steel, so are confirmed...

Low Profile Bed Clamps for the Kossel Pro These bed clamps sit only 2mm above the print surface, which greatly improves the printing area compared to the stock bed clamps. The screw heads are recessed so that they sit flush with the bed clamps. This...

A nice simple low profile bed clamp for the Kossel Pro. This replaces the tall bed clamps that came standard with the Kossel Pro, which interfere with the printhead when it's at the edge of the bed. Made in OpenSCAD, file included, there's not much...

... CNC. You can use the straight angle to unable your stock to slide underneath the clamps. ... I have made the holes of the steel bars slightly undersized to be fit the bar tightly but you might check the accuracy you get out of your printer.

As you tighten the screw, the clamp will move forward. This is currently designed for machining from metal. Printed versions have not been tested. Due to stress, 70% infill with 3 walls would be recommended. ...The hole might need to be enlarged for...

REQUIRED HARDWARE: (for 1x clamp) 2x m3x10 or longer 2x m3 nuts Link for the specific nuts that I keep in my shop for basic general use parts (I will not be maintaining amazon links as they change rapidly):...

Low profile clamps for CNC, inspired by OK-Vise (http://www.ok-vise.com/). Designed for M5 screws. ... Print them sideway for less friction.

Wanted to keep the clamp as low as possible to minimize Z height loss. The centerline of the rod is 9.3MM above the surface of the 2020 extrusion. This is sized for M5 screws to clamp to the extrusion and an M3x16 cap head screw and captured nut...

Low profile CNC clamp for applying side and down pressure. Stop block and T-nut included. T-nut can be purchased, printed, or CNC/laser cut. Design for common T-tracks. ... ___Hardware___ __Clamp__ 2x 3/32 x 1.25" dowel pins 1x #10-32 x 3/4" Cap...

Clamps for conveniently holding down a 250mm borosilicate glass bed with applied Kapton heater. ...Low-profile for maximizing printable area. ... openSCAD file is included to enable you to fine-tune to your needs.

A low profile workholding clamp for CNC usage Print instructionsThis is a work in progress Uses: 1x M5 16-16mm socket screw for the sliding part an M5 nut to fasten it to on the base 2x M5 washers 2x 5x25mm steel pins The pin holes are modeled...

This is similar to low profile CNC clamps you can purchase however i wanted to adapt it to use on my CNC waste board which has insert nuts, and dog holes. Will be printing this over the weekend and will update ASAP. It's made to suit 6.3mm...

This is similar to low profile CNC clamps you can purchase however i wanted to adapt it to use on my CNC waste board which has insert nuts, and dog holes. Will be printing this over the weekend and will update ASAP. It's made to suit 6.3mm pins in...

Designed for 1/4-20 screw (for the central part) and a 5mm socket screw to hold everything together. This is currently designed to be machined from metal. ...Printable version will be coming soon after testing.

This is a low profile clamp which is especially useful if your CNC is equipped with a dust shoe. It exists in two sizes: 80mm and 110mm. The width of the slot in the middle is 5.4mm (ideal for use with M5 screws - e.g. ...X Carve).

Low profile clamps for CNC, inspired by OK-Vise (http://www.ok-vise.com/). Designed for M5 screws. Print them sideway for less friction. This is a remix from my previous work, the dimensions are reduced to fit a 20mm v-slot, and the jaws are...

... 20cm from the bottome of the desk. I created this clamp (print 2) to fit into the existing slots on the racing wheel and allow you to bolt through the desk or stand. ... All you need is 4 x M6x70mm bolts with some M6 wing nuts and you're away.

In order to hold stock of different sizes i had to resize the foot in order to be be able to clamp it down to the available holes. So i created 3 different versions as you can see in the photo. I hope that you find it usefull. ...

The main change was to remove the filet on the base and slider that was causing the piece being clamped to lift. Hardware used: M5 Heated insert https://www.amazon.com/gp/product/B08GHNJWLS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 ...

Other advantage, besides being low-profile is that it clamps a larger portion of the belt, therefore helping to reduce potential belt slippage as well as it looks MUCH sleeker. ... I printed mine in Proto-Pasta carbon fiber filament at 100% infill...

Clamp to be used in T slot working table. -2pz. 5mm X 25mm. stainless steel bars.(They enter under pressure). -1pz. 4M X 16mm. Socket Head Allen screw. (Tap Drill 3.3mm). -1pz. T nut with its screw. ...(Use according to your working table).

... 6mm rod, everything else is the same. ... Brilliant little clamp. UPDATE Added base_lon.stl file to fit a larger hole spacing on waste board, still 6mm rod and rest as the original. ... Original file https://www.thingiverse.com/thing:3835369

This is my version of a low profile toe clamp. I made two versions one with a "standard" type top and one with a very low extended nose top. Both versions use the same base. It uses M5 hardware (Cap screw and Nut) and two 1/4" diameter guide rods...

(There is no text on the parts!) Inserted the Spool Clamp due to comments within other variations of the Spool Rollers having issues with the Spool falling off. Requires: 1 Print for the Spool Clamp 2 Prints for the Spool Holders Total of 2 bearings...

The originals work very well but as part of my upgrade, I have done two things Installed a magnetic PEI Flex bed in place of the glass one Installed a BL-Touch on my custom mount on the rear of the X carriage For this reason, I needed to change this...

The blower I liked hit the stock simple clamps the BIBO came with and I could not find one low enough profile to fit under the blower. The blower in question: https://www.thingiverse.com/thing:2973360 These are also nice because you can put in a...