makerbase mks tft35 3d models

This will fit the MKS Mosfet to the Anet A8. The ones I found on here were for the A6, and just turning them made a problem with the mosfet blocking the USB plug and the card slot. The two holes/spacers will replace the original top spacers on the A8...

I got 2 of the MKS Hotbed-Mos+ V1.0 (Picture is in the Files) and wanted to use them for the Bed and the Hotend to get all current away from my Mainboard. I made that holder to mount it nicely to the Printer. You need to drill holes to mount that...

This is a Remix of the MKS_DL V2.0 case. It now Fits to the DLC 32 an has a hole for an ON/OFF Switch and the SD-Card Slot. It is 7mm higher than the Original Version, so that you´ve got more space for the electronics and it´s possible to mount the...

The new TFT Screen 2.0 from MKS Robin is a game-changer, designed to take your gaming experience to the next level. This cutting-edge display boasts an impressive resolution and vibrant colors that will transport you directly into the action. With...

I wanted to install my MKS Monster8 on a DIN rail, and saw the design on https://voronregistry.com/mods/clee-monster8dinrailmounts. As I didn't have any heatset inserts, and the part that attaches to the DIN rail is to stiff when you print it in...

With these components removed, I rebuilt the printer using an MKS-Base v1.5 / MKS-TFT 28 v3.0, replaced the original extruder with a J-Head (with modifications), and rewired it slightly differently. The result is what you see in the photos: a...

One is a basic case and lid for the MKS Gen Board, while the other is a case and matching lid that also accommodates the optional external mosfet for the heatbed. The design features a USB cutout and a hole for a 20mm OD spiral cable conduit,...

Stand for BIGTREETECH TFT35 E3 V3 Screen. Fixation by the top. ... Initially intended for 3DTEVO (TEVOUP) Little Monster printer

The new and improved BIGTREETECH TFT35 V2.0 is specifically designed to fit perfectly on the Ender 3 case.

This is my custom mount for a MKS SKR 1.3 Board on my Hypercube Evolution. It can also hold a raspberry PI, on which I run OctoPrint on. The two boards are connected over a direct serial connection via GPIO. I took the step on controll the SKR board...

The top portion remains unchanged, so please use Stage_Monkeys brilliant design, while the main case part has been adjusted to accommodate an MKS 1.4 board. This modification removes the ability to utilize Mosfets! I have uploaded the .step file...

Hey everyone, I've got a brand new case/box for the mks tft32 touch screen that comes with a range of different holder/joints to make installation super easy. These holders are perfectly compatible with 2020 aluminium bars. In this video, you'll see...

I designed the MKS Board Mount to facilitate easy access to the board, ensuring it can be located on the side and sit sideways, thus freeing up more space next to the bed. The original acrylic top was retained for this design, but an STL file of a...

Hello, This is my prototype for the MKS MOSFET Case. It's still a work in progress, but I'm excited to share it with you. The bill of materials (BOM) includes: - 8 M3 nuts and bolts to secure the top to the bottom. - Double-sided tape to attach it...

Hi, a brand new housing for mks sbase electronics v1.3 that I created specifically for installation on my tronxy x5s :)\r\nI added a version with a closed bottom to use on 2020 aluminium bars. In the video, you can see the box and the installation...

The MKS-HV75K-N ServoSKU features a high precision control system with a default dead band of 0.001ms, working at frequencies of 1520μs/333Hz. It operates on a voltage range of 3.7 to 8.2 V DC (for 2S to 1S LiPo), in temperatures between -10°C and...

The MKS Mosfet base from S3bape stands out as one of the most rugged large mosfet mounts on Thingiverse, boasting a sturdy design that can withstand rough handling. However, its open base leaves it vulnerable to damage from prying fingers or other...

MKS Robin Nano case with "3.5 tft" touch screen. The two pieces are joined by M3 screws. ...I used brass inserts so one parte of the hole is always bigger</p> <p>There are also holes to attach two 40mm fans on one side (the one close to the drivers)</p>...

Here's my custom enclosure for the MKS Rumba+. The case is a bit taller since I'm using TMC2100 with stepper protectors. There's no mini USB port opening because I use the 4-pin USB header on the board to connect it. When you plug in the motor...

I designed a snap fit case specifically for the MKS TFT 3.2" screen, ensuring that no screws would be needed to secure the screen or assemble the case. The case was printed with an accuracy of 0.2mm using high-quality ABS material and vapor smoothing...

This screen housing designed for BTT TFT35 V2.  BTT_TFT35_V2_HOUSING.stl  designed with the same mounting dimensions as in  BTT TFT35 V2. It means that you can attach it to any 3D printer with a flat front panel and with the same mounting dimensions...

Here's the list of components bought to fit into the case: * MKS Gen L 1.0 controller: https://www.amazon.com/dp/B07BFSMTPS * DC-DC voltage regulators: https://www.amazon.com/dp/B01GJ0SC2C * Printer bed controller:...

... bolts to fix the boards to the case and then the lid to the case - you're good to go! Please note that this case is designed specifically for the MKS board Gen L and MOSFET model; the screw holes may not fit other types of MOSFETs or control boards.

To create this project, I used an MKS Gen V1.4 board with two MOSFETs installed. This fan holder is perfect for a 120mm fan as well - just keep in mind that one piece is enough if you want to print it that way, but feel free to print two pieces...

Hey, I'm excited to share a brand new housing for mks sbase electronics v1.3 that I designed specifically for installation on my tronxy x5s :)\n\nI've included an updated version with a closed bottom design to accommodate 2020 aluminium bars. Check...

It's a bracket designed to attach an MKS board to the top shell screws of a salvaged Dell PSU. The holes are proprietary, likely due to their unique design. When referencing this setup, keep in mind that AC-In is positioned on the left, accompanied...

Hey there, I've got a brand new case/box for the mks tft32 touch screen that comes with a range of interchangeable holder/joints to make installation a breeze. These holders are perfectly compatible with 2020 aluminium bars. Check out this video for...

Simple Adapter for the Anet A8 Fram to mount @3Deddy's Slim and Elegant BTT TFT35 V3 Touch Screen Extrusion Mount

Anycubic 4Max SKR TFT35 E3 holder The model fit to the original place. ...No need drilling or any modification on the housing.

Mise à jour suite au mauvais placement support arrière Support Ecran BIGTREETECH TFT35 pour Sidewinder-X1 Filament PETG Résolution 0.2 Support