makerbot z18 filament holder 3d models

This spool holder is designed to fit tightly onto the back corners of a Z18 (with top cover removed). After you push them tightly in place, they will be rigid like extensions of your printer. This structure is optimized to withstand vertical loading...

1kg MakerBot filament spool holder for 5th Generation MakerBots by admg consultancy This will work on the 5th Generation Replicator, the Z18 and the Mini. It allows use of MakerBot 1kg filament spools, while retaining the captured filament guide...

External spool holder for Makerbot Z18. ... 2x CHC M4 x 16 and 2x M4 nuts needed

a holder for attaching a plastic coil on the side from above.for Makerbot Z18.

You can edit or change your own here: https://www.tinkercad.com/things/ilrYKd1pp6d-z18-spool-holder Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Doesn't Matter Supports: No Resolution: .200 Infill: 10 Notes: Print each...

Wanted to mount spools directly overhead the z18 printer. You will also need 1" PVC pipe 19 3/4" long. This is a quick, down and dirty, Tinkercad.com need something now piece. You can edit or change your own here:...

... overhead the z18 printer. ... You will also need 1" PVC pipe 19 3/4" long. This is a quick, down and dirty, Tinkercad.com need something now piece. You can edit or change your own here: https://www.tinkercad.com/things/ilrYKd1pp6d-z18-spool-holder

Z18 Spool Holder. ====================== Need the following steel parts: * 608ZZ bearing : 2 * M8 thread 25cm * M8 nuts ; 2 at least. 3 is better. Insert 608ZZ bearing on the top. And put the thread into the bearing. ...And use nuts on...

I bought some PLA filament spools with hole 30mm diameter in the center. And the width is about 85mm. I used to use http://www.thingiverse.com/thing:615307 for larger hole spool, but 30mm hole is too small for it. So I use openscad to create a...

Remake for Z18 of Universal stand-alone filament spool holder http://www.thingiverse.com/thing:508896

Remake for Z18 of Universal stand-alone filament spool holderhttp://www.thingiverse.com/thing:508896

I was looking for a Spool holder for my z18 but I didn't find anything I liked so I created one... Print this on its side for best results! Check out the Pictures\. Hope you like it!!! ...

As with all Makerbots this has the dumb old fashioned filament tube that causes 90% of filament jams, so I made this top mounted spool mount that does not require the tube and feeds the filament directly to the extruder but as I hate spending 20...

As with all Makerbots this has the dumb old fashioned filament tube that causes 90% of filament jams, so I made this top mounted spool mount that does not require the tube and feeds the filament directly to the extruder but as I hate spending 20...

The filament guide on our smart extruder broke and so we remixed Wurstnase's Modified Threaded Filament Dust Filter - Replicator 5th Gen. This model requires less support as it has a flat bottom. ...We are currently testing the design on one of our...

Modified Spool holder for side mounting designed for Makerbot Replicator Z18. ... Tested for use with Colorfabb & Robosavvy 1KG Spools of PLA Print using standard profile with raft & supports with 30% infill and 4 shells.

... with the Replicator Z18. ...No need for a complicated hanging mechanism, just stick this on the top corner of the printer and feed the filament through the side opening. ... Designed to print in one piece with no supports and no post-processing.

After realizing the bottom spool holder has many issues due to friction we started using the spool holder MakerBot recommends, https://www.thingiverse.com/thing:615307, and while this works, we very much disliked that we couldn't secure the top and...

... it with fusion 360. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Z18 Rafts: No Supports: No Notes: Makerbot logo is a registered trademark of MakerBot Industries, LLC One MetroTech Center, 21st Fl, Brooklyn, NY 11201 USA.

The idler pulleys at the front of my Makerbot Z18 are made of steel and they have a steel shaft. One of these pulleys sheared off under stress and the other is showing signs of wear because there is no bushing on this connection. We made this idler...

Using a clever combination of EL Wire and conductive paint, hackers have discovered a creative workaround to turn off or adjust the lights on Makerbot's expensive, yet limited $7,000 3D printer.

With Makerbot's $7,000 3D printer finally arriving on the scene, there's now a need for controlling those dazzling display lights that glare brightly with each and every turn of operation, and a smart workaround could be exactly what users are...

... from a soda can. An M5 bolt is inserted through the front. Update 9-Aug-2016 Better fitting version with bolt turned around, previous design had a problem with filament on the threads and sometimes came loose. ...This version is a lot better.

MakerBot Industries now sells filament on spools, so you can print a spool holder to replace the rod cover on your Thing-O-Matic or Cupcake CNC. Additionally, print a spool housing to keep filament neat and tidy. Visit...

The ideal way to utilize your new MakerBot PLA Filament Sample Pack is by printing a 0.25 lb spool holder and attaching it to either side of the rear of your MakerBot Replicator Desktop 3D Printer (Original) or MakerBot Replicator 2 Desktop 3D...

Edit it online https://www.tinkercad.com/things/hSbJFvw4x3N How I Designed This Makerbot filament holder Made this so I could store the filament in the bags they came in. Keeps them from absorbing moisture. It also is a good way to see just how...

Organize your filament effortlessly with our stylish wall-mounted holders, available in various colors to match your stored material. The photo offers a visual reference. To assemble, print at 0.3mm layer height with a 13% fill using ABS on a...

This is a Dustfilter for the MakerBot SmartExtruder+ for the Replicator Z18. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator (5th Generation) Rafts: Yes Resolution: 0.1 - 0.15mm Infill: 15% Notes: Print "...Top6" with support and...

This is two parts to be used on maker bot mini to use full spools of off brand filament. ... Note the spool holder must be removed to install a new spool.

When the MakerBot spool can't fit into your printer due to its size (9.84 inches).