map marker 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The model shown has six in each ring for a total of twelve. Print one of each of the remaining files. Carefully remove any burrs or imperfections in the print especially on surfaces that move against one another. The “Spinning Terrain” prints...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

phone_model_customized = Yes, it is now set at 0 custom_left_port_y_position_disabled = No, has been set by the default of 0 as requested above bottom_port_corner_radius_customization_enabled = Yes, now has a custom setting equal to 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

and all they could offer was to return the toolbox completely or bring in the suspect drawers and swap with floor models…This drove me nuts on an otherwise perfect toolbox and I had to fix it...The FixI designed new end-caps to enclose the aluminum...

Just make sure to get the alignment correct before letting the glue set up!Notes:Raft:              YesSupports:    NoI've had the best luck printing these using a single-layer raft, with the part oriented...

To assemble: Note - this is a somewhat challenging model to assemble, with a lot of parts, and a lot of tight-fitting pins to hold the parts of the toy together. You may also have to clean up a lot of support off the oddly-shaped pieces as not much...

Be very careful when inserting the blade.* Huge respect to Alexey Pavlenko for the idea of adapting the popular knife from Giacomini for printing ===================================== PS 21.03.05 I updated the files of this model. If you downloaded...

To do this I went to https://3dp.rocks/lithophane/ sized it in model settings, and set it to Positive under image settings. I kept it flat since it will be used as the back of the bookstand. But while it's not in use it can also be used as a cool...

If you want to save time while testing, you can print the included calibration test instead of the full model, but that is optional.Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It may feel...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

The model is amazingly easy to fly. https://www.youtube.com/watch?v=rsS5YetUQyA The video quality is less good - this time I had to film myself. <iframe width="684" height="385" src="https://www.youtube.com/embed/rsS5YetUQyA" frameborder="0"...

In the fanduct file they are included in the model. You will need: - x2 radial fans 5015 of 12 V. - x2 M3 screws of 25 mm. (To hold the fans above). - x2 washers for the M3 screws. - x2 M3 screws of 20 mm. (To hold the fans below). - x4 M3...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

... If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

If there's interest, I can also upload the design files for other models. Please share your creations if you remix. Update: The original inner joiner STL was undersized. I've added a new STL that should be properly sized with everything else in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

think about it like drawing line art, not solid modeling shapes in CAD). 6. Print with a layer height of 0.25mm or less. Much more than that and the slight bulge on each layer will grab the dough, making it harder to demold. We used 0.2mm layer...

The COMPLETE Dumlok Flameseekers bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: 12 Dumlok Flameseeker (modular figures + figures with helmet)The Dumlok,...

&nbsp;For me, it pressed in very tightly; if in doubt, glue it in.To mount the holder, I stuck this adhesive mount onto the back, and used it to replace the jaws of an older model of this suction base. &nbsp;The adhesive mount’s socket is smaller...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

- Replaced PZ20 circuit's LDO with a simpler model with higher input voltage range - Added second LDO for dedicated supply to LED's - Isolated TH1 from ground plane to address vdroop effecting thermal readings - Added grounding vias for edges and...