marble spinner 3d models
31906 3d models found related to marble spinner.sketchfab
Atom marble spinner. For those moments when your feeling fidgety and trying not to lose your marbles. ... I also made on my 3d printer.
thingiverse
Don't lose your marbles. ...Printed 50% infill layer height 0.2000 support: yes Used hot air gun to heat up middle of spinner and then pushed the bearing in. ...Glued the marbles in place.
thingiverse
2016/01/21 Updated design, more stable design for better spin This Spinner is made up from: -1 pc printed part -3 pcs 16mm marbles pressed in with a bench vice -1 pc 608ZZ bearing/skateboard bearing (pressed in) -2 pcs printed bearing caps (glued in)...
thingiverse
Inside hole is for a 608 bearing and the outsides are 16mm holes for marbles. Marbles pop right in and are secure without any adhesives. Designed using solidworks. ...Let me know of any tips to make the design better and post yours to the Made if you...
thingiverse
I really liked [growe41's Atom Marble Spinner](https://www.thingiverse.com/thing:2166485) and remade it in OpenSCAD for better marble grip. You can change marble diameter and most other dimensions in customizer. Included STLs are for 15-15.5mm and...
myminifactory
https://www.tinkercad.com/things/bGdYfXXbSSj Spinner, using marbles as a bearing. The center hub can be resized or sanded to improve overal fit. On mine, I sanded the hub (the points on the inside) to make it shorter so that the curves would help...
thingiverse
... on net. ...Layer height: 0.2000 Infill: 50% Support needed Used ceramic bearings for better spinning, got off aliexpress. Glued in marbles because they were different sizes. You can view an interactive 3d model of the spinner at: https://skfb.ly/66nBx
youmagine
... on net. ...Layer height: 0.2000 Infill: 50% Support needed Used ceramic bearings for better spinning, got off aliexpress. Glued in marbles because they were different sizes. You can view an interactive 3d model of the spinner at: https://skfb.ly/66nBx
thingiverse
There are several of these, but I wanted a spinner that allow both an easy introduction of the marbles and that really prevent them from getting out of the fidget when rotated. Unless throw the spinner on the floor. Marbles will remain in place. I...
thingiverse
removed knurling from around bearing to strengthen design, created sleeves to hold 16.5-18 mm marbles, edited thuimb screws to allow spinning on flat surface
thingiverse
We have a lot of marbles around so modified a couple spinners to use 15.5mm marbles instead of steel weights or bearings. (Standard Marble size is about 15.5 - 15.7mm) They are made where the marbles can be changed out if they want to mix or have...
thingiverse
There are several of these, but I wanted a spinner that allow both an easy introduction of the marbles and that really prevent them from getting out of the fidget when rotated. Unless throw the spinner on the floor. Marbles will remain in place. I...
thingiverse
Customized version of http://www.thingiverse.com/thing:2366552 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2366552
thingiverse
to be fair, I didnt use marbles from a marble set, I used marbles that i cut out of spray paint cans, but if they are the same size they should work fine. I plan on uploading a version that works with steel bearings too. ...as you can see one of the...
thingiverse
Customized version of http://www.thingiverse.com/thing:2366552 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2366552
thingiverse
Customized version of http://www.thingiverse.com/thing:2366552 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2366552
thingiverse
Customized version of http://www.thingiverse.com/thing:2366552 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2366552
thingiverse
Customized version of http://www.thingiverse.com/thing:2366552 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2366552
thingiverse
Customized version of http://www.thingiverse.com/thing:2366552 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2366552
thingiverse
Customized version of https://www.thingiverse.com/thing:2366552 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2366552
thingiverse
Customized version of http://www.thingiverse.com/thing:2366552 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2366552
thingiverse
Customized version of http://www.thingiverse.com/thing:2366552 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2366552
cults3d
my favorite spinner design so far based on D15-D15.5mm marbles needs 1x 608 skate ball bearing and 5x D15 marbles depending on print result, marbles may need a little force to go in, but move freely inside their pockets for additional fidgeting model...
myminifactory
my favorite spinner design so far based on D15-D15.5mm marbles needs 1x 608 skate ball bearing and 5x D15 marbles depending on print result, marbles may need a little force to go in, but move freely inside their pockets for additional fidgeting model...
thingiverse
for those of us that cannot sit still I made a fairly cheap fidget spinner that uses 5 marbles and a longboard ball bearing. ...INSTRUCTIONS: lay it flat in slicing software and then make sure that the height for the z axis when object is flat is 7mm...
thingiverse
120 x 50 x 9mm (Marble 25mm) 1u45min Print Inset marble creates an illusion of up and down movement as it spins