marzel vanes 3d models
1309 3d models found related to marzel vanes.thingiverse
Customized version of http://www.thingiverse.com/thing:1148986 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1148986
cults3d
Print in tpu. ...These are my quietest 2.25 inch vanes I have designed and one of my favorites for hunting and target practice.
thingiverse
This is a replacement part I create for a little windmill I have. ... I found that the first version looked better but didn't turn in the wind as it should, so I created a second version with wider vanes that are more steeply angled.
grabcad
Guide vanes - digitization drawing (Элемент направляющий - оцифровка чертежа)
cults3d
Iris Vanes Door BOX 5 Iris vanes that move closer as you tighten the lid of the container. ...Like the Iris inside a camera
thingiverse
Iris Vanes Door BOX 5 Iris vanes that move closer as you tighten the lid of the container. ...Like the Iris inside a camera
thingiverse
This is a File for Fusion 360 to create your own 3d Vanes. You can customize every thing to your needs in the user parameters. ... I'd recommend using TPU as printing material Use at least 10 Lines of Brim
cults3d
You can print each part in halves or in one piece as long as the previous needed parts: vane_1_p1_h1.stl vane_1_p1_h2.stl vane_1_p2_h1.stl vane_1_p2_h2.stl vane_1_p3_h1.stl vane_1_p3_h2.stl vane_1_p4_h1.stl vane_1_p4_h2.stl letters_base.stl...
prusaprinters
You can print each part in halves or in one piece as long as the previous needed parts:vane_1_p1_h1.stlvane_1_p1_h2.stlvane_1_p2_h1.stlvane_1_p2_h2.stlvane_1_p3_h1.stlvane_1_p3_h2.stlvane_1_p4_h1.stlvane_1_p4_h2.stlletters_base.stlletters_bar.stl...
thingiverse
This is a fan grate with turning vanes that I designed out of necessity. The fan that I put on the side of my Prusa enclosure was blowing slightly across the build plate. This part is astonishingly effective at turning the airflow down to the bottom...
thingiverse
Made arrow vanes/fletchers that can be printed in vase mode that slides on to a 8mm wood dowel or pipe. Also made an arrow tip that can be pushed on to the top. Have gone throu multiple iterations and recorded the arrows in mid air in slowmotion...
thingiverse
A model of the compression and guide vanes of a jet-turbine engine.
thingiverse
PRINT IT AND SHOW YOUR MAKE ! ...Experimental replacement vanes for Rockyman Water Rocket. I needed replacement vanes because the original were broken. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/51hpHRIZDzt
myminifactory
... with the existing light holder and base and assemble in the same manner. You will need to print 8 vanes and 1 of each of the remaining parts, the vanes are 1.8mm thick just like the origional design so it will have similar light dispersion.
thingiverse
The profiles of the buckets, guide vanes and guide vane hubs are described as a set of points in the relevant modules, so to change the profiles, you could change these points. Hope this is of use to someone, feel free to use and modify as suits your...
thingiverse
The vanes may be a little closely spaced for some grind levels, but it hasn't been enough of a factor for me to fiddle with it. ...I THINK the hole spacing is correct now, but I'm terrible with fixing this kind of stuff and it worked great on the...
grabcad
The radial movement of a vane according to the cam profile is allowed thanks to a small wheel, which rolls inside a guide following the cam profile, and is connected to the inner end of the vane (i.e, the extremity of the vane close to the bucket...
thingiverse
Impeller (vanes) for cooling the electric motor
thingiverse
combined a 40mm to 30mm adapter with the original vane
prusaprinters
combined a 40mm to 30mm adapter with an included vane
thingiverse
The back side has a slight chamfer around the outer ring to help the vanes sit flush in the opening. I chose to screw mount mine so I can take it off and change it out. I also change the color behind the vanes to a darker color for looks. ...
thingiverse
This is a fan grille for an 80mm fan, with 7 vanes. It will be guarding the fan ducts for an upcoming MTU IEEE thing, keep your eyes posted! Update: added DXF file as requested. ... Instructions Print...
thingiverse
... that dimensions needs some adjustment for correct fit. This will be updated on short notice. My design replacement vanes for Rockyman Water Rocket. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/51hpHRIZDzt