masterbox q300l ssd mount 3d models

And the miscellaneous trim and clips and joiner parts are another hour or so. Assembly requires:  a quantity of 10 m2.5 x 6mm screws (I used Fastenal # QM2490006A20000) a quantity of 19 m3 x 6mm countersunk screws (I used Fastenal...

updated the HD mount for the back of the iMac for my late 2019 27" imac and the two hard drives I constantly have attached. ...Tinkered it at: https://www.tinkercad.com/things/iioBb93Ef1X-lacie-imac-hd-mount

This is the successor of https://www.printables.com/model/293801-samsung-t7-mount-adhesive-mounting and allows attaching one or two Samsung T7 SSDs to an iMac stand.The SSDs are clipped into the holder, the holder is then slid over the iMac stand and...

Adapter to mount 2.5" drives in systems that are designed for bottom-mount 3.5" drives. This is particularly useful for various systems that use drive trays/sleds - I'm using one of these to mount a 2.5" SATA drive in an old Macintosh Performa 630.

This is the successor of https://www.printables.com/model/293801-samsung-t7-mount-adhesive-mounting and allows attaching one or two Samsung T7 SSDs to an 27″ iMac stand.The SSDs are clipped into the holder, the holder is then slid over the iMac stand...

Dual 60mm fan mount to cool your HDD/SSDs on the LianLi O11 XL Just attach the fans like shown in the pictures and route the cables through the grooves.

This accessory is intended for use with any 120mm case fan, allowing it to be securely fastened to the front of the Cooler Master Masterbox Q300L PC case. By adding 10mm of clearance between the fan and the steel panel, it significantly reduces noise...

Reinforced the mounting mechanism to allow the printed piece to be pushed onto the 7,5mm studs on the PSU-wall. Uses the factory screws that came with the chassi to be used with those holes. I used supports on the holes that pushes on the studs.

The adapter friction fits existing mount points designed to keep ODD in place, no additional fixtures are required.For SATA power I used a hand-made adapter from a SATA power cable cut from another PC PSU with a 4-pin header soldered to it. ...Always...

Remixed from the original: https://www.thingiverse.com/thing:4178847 to fix a few issues I found for my use case: - walls are slightly thickened - Doubled to support 8 drives instead of 4, would not recommend mounting HDDs though, just SSDs. - Added...

This allows you to fit twice as many drives in old cases that didn't have 2.5" mounting holes, like the one I'm using for my NAS. The drives have enough room to breathe on all sides and are also separated so they don't release their vibrations into...

A mount I designed to mount a SSD to the underside of a table.

This is an Enhanced Version of the SSD Stackers, optimized for thicker SSDs and HDDs up to 15mm thick.\r\n\r\nFurthermore, I have reworked a mount for the uppermost SSD or HDD, allowing it to be securely fastened to the wall using standard spacers on...

This is an NZXT-style cable management bar for the Cooler Master Q300L. ...To fix it I used the holes for the SSD and their rubbers pads (included in the box).

2.5 SSD To 3.5 Hard Disk Mounting Internal Adapter.Soporte adaptador de montaje de disco duro de 2.5 SSD a 3.5 HDDMejor imprimirlo en PETG u otro material técnico que aguante el calor.

(just take a look at my codes and do like them)Print the 1U rack-mount  base on the diagonal of your print bed, just like the photo belowHow to assemble and required hardware:To attach SSDs to the Rpi module, you need M3x3 or four bolts (4 for...

This print is created to replace the original front of the CoolerMaster MasterBox TD500. The original front is nearly closed, so the fan are not very efficient. This print brings a regular grill. ...I splitted the grill in two half to make it printable...

These are custom 3D printable U-Shaped feet for the Cooler Master Masterbox NR200P SFFPC case !! I am in the process of doing a mod on mine and developed this custom foot design as part of the project. I printed them with 5% infill and 4 walls, I'm...

This is a mounting Tray to fit an SSD into a dell optiplex 9020 (also fits some other models). It is a single piece solution to replace the blue dell caddy and 3.5" to 2.5" adapter. I have been using these sucessfully now for over a year. ...I will...

Default size is for Seagate Backup Plus, but in slicer, you can adjust size for any hdd, like me. ... Enjoy!

This is a remix of https://www.thingiverse.com/thing:3974307 I raised the walls with 4mm to get enough room for my Sata to USB adapter to fit in the case Also removed the writing to get a cleaner print. Update: (file with (1) is new with the...

Here is the official .STL for the plastic clips used in the NR200 and NR200P to secure the panels to the body of MasterBoxes NR200 and NR200P, in case you need some spare ones ;) Please be noted: This file is distributed under the CreativeCommons...

This is a mounting Tray to fit an SSD into a Dell OptiPlex 9020 (also fits some other Models).\nIt's a Single Piece Solution to replace the blue Dell Caddy and 3.5" to 2.5" Adapter.\nI have been Using These successfully now for over a year.\nI will...

I did this support to organize my SSD inside the computer cabinet. ...The latch is better to fit underneath up. Fiz este suporte para organizar o meu SSD dentro do gabinete do computador. A trava é melhor encaixar debaixo para cima. ...

Currently working on a side panel mod for taller CPU coolers, and a top-mount radiator design for the NR200P, but this is gonna take time with some calipers and to test properly... DM me if you want the SolidWorks model or whatever to CAD it if...

... between hard disks, and one with +10 mm for more air flow (***_large). Step files for easy modifying also present. Predisposed for: 2x 3.5" hard drives 1x 2.5" ssd (for example unraid cache drive) Easy vertical print with brim and no support

Required for mounting SSD's in older laptops

... specifically for this case. ...If you're interested in a model optimized for 200mm printers with detailed documentation, it's available on Pinshape: https://pinshape.com/items/55309-3d-printed-q300l-q500l-coolermaster-pc-case-mesh-side-panel-extension

A conversion bracket for mounting a 2.5" SSD in the mounting position for a 3.5" HDD underside screw. Designed for retrofit installation of SSD drives in LeCroy WaveRunner 6000 Series oscilloscopes. ... ...

ssd disk