mean well sp 320 24 3d models
306265 3d models found related to mean well sp 320 24.thingiverse
Designed special for SP-320-24 Mean Well. ...Suitable for install on Ender 3 -- Reccomend to print in with 101-102% scale
thingiverse
Replacement top cover for a Mean Well SP-320-24 power supply with mounting holes for a 100mm fan. This power supply shipped with the Monoprice dual extrusion and some of the other Replicator clones like the Flashforge Creator Pro. The stock 60mm...
prusaprinters
A cover for a Mean Well SP-320 power supply to stop young fingers from getting at the mains connections. I used the basic form and size of STB's cover with the power connector and switch from Mortorojo's cover for a different sized power...
thingiverse
A cover for a Mean Well SP-320 power supply to stop young fingers from getting at the mains connections. This design will allow the power supply to be attached to the left side of a Prusa i3 sheet frame (e.g. the MakerFarm kit) with easy access to...
thingiverse
MEAN WELL RSP-320-24 holder for Bear upgrade.
thingiverse
This is a lid for the Mean Well SP-240-24 PSU, intended to keep fingers safe from the mains connection while still allowing air to enter the PSU. The existing side holes are not covered, and the lid goes to the screw holes for permanent mounting if...
grabcad
Meanwell SP-320-24 powersupply.320w 24v 13a Drew it up as I needed some brackets to mount it under my BeTrue3D CoreXY printer.
thingiverse
... Well RSP-320-12 Power Supply. ... I designed this for the Power Supply that I used in my D-Bot build since there was no cover for the newer thin model of the power supply. Designed for this modelhttp://www.mouser.com/ProductDetail/Mean-Well/RSP-320-12
thingiverse
A bracket to screw a mean well power supply onto a boardhttps://cad.onshape.com/documents/ba67fcddb8b7d887e930bf61
thingiverse
Remix for the RSP-320 ones. --- https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version...
grabcad
The Meanwell MDR 20 is an item inspired by the meanwell MDR-10 by Marinus Jeuring which can be found at Mean Well MDR-10
thingiverse
Original is not bad, but i trust more mean well brand. This new PSU have temperature controlled fan 40x40x20 with load combination. And Active PFC correction, very stable voltage under load. Is not quiet, that is true, because fan started at 50C or...
grabcad
Mean Well 24v Power supply.**UPDATE**It has been brought to my attention that the vendor drawing has the width of the PSU at 115 but my model is at 114. These dimensions were taken from my power supply that measured 114.16 that I was using at the...
thingiverse
Cache pour alimentation Mean Well Sp-240, sans bouton on/off.
cults3d
Hello... This is a wall mount adaption from the original ZARIBO Meanwell Case. I mount it behind my IKEA Platsa. ... The holes are hitting both boards in the middle for a stable mount.
thingiverse
Hello... This is a wall mount adaption from the original ZARIBO Meanwell Case. I mount it behind my IKEA Platsa. ... The holes are hitting both boards in the middle for a stable mount.
grabcad
Outer shell and mounting holes for Mean Well LRS-350-24 Power Supply 24voltbased on dimensional drawing in pdf
thingiverse
Made a safety hood for the MEAN WELL LRS-350-24, it may or may not fit other Mean Well PSU's. Good luck. ... Step file included in case you want to make modifications.
thingiverse
Power supply holder for Mean Well RSP-500-24. Designed to sit across two 2020 rails. ...160mm from rail center to center.
thingiverse
Power supply Mean Well LRS-350-24 and XT60 plug XT60 connector panel mount - https://www.thingiverse.com/thing:695374 XT60 enclosure mount - https://www.thingiverse.com/thing:3113398
cults3d
Power supply Mean Well LRS-350-24 and XT60 plug XT60 connector panel mount - https://www.thingiverse.com/thing:695374 XT60 enclosure mount - https://www.thingiverse.com/thing:3113398
thingiverse
Case for *Mean Well LRS-75-24* PSU. Has slot for a 4.9x2.9 cm power inlet module and a DC 5525 jack socket plug for output. Note that I left a 0.2mm gap along the [horizontal section](https://imgur.com/BYsQa1a) where the case and lid meet. ... Link...
prusaprinters
I designed this PSU cover for the Mean Well LRS200-24 PSU.The model files contain one “normal” cover and one with the VORON Design logo (i originally designed this cover for my VORON v2.4).
prusaprinters
Has slot for a 4.9x2.9 cm power inlet module and a DC 5525 jack socket plug for output. Note that I left a 0.2mm gap along the horizontal section where the case and lid meet. Link to the cad model I used as reference:...