mecreator 2 3d models

MeCreator 2 Fan Shroud

A filament guide for MeCreator 2. ...Print Settings Printer: MeCreator 2 Supports: Yes Resolution: 0.2

... the PVC pipe that came with the printer. Designed in SketchUp. The model will fit on the print bed of a MeCreator 2. Print Settings Printer: MeCreator 2 Rafts: No Supports: No Resolution: .2 Infill: 50% Notes: Printed in ABS, but PLA should work.

Just a simple camera mount designed to use zip tie to hold camera in place so it should fit just about any webcam. ...Print Settings Printer: Geeetech Mecreator 2 Rafts: Doesn't Matter Supports: Yes Resolution: .15 Infill: 20

I made theese feet for the MeCreator 2 to lift the bottom and give about 35mm clearance. I removed the noisy 35mm case fan and added a 10x80mm fan and a new opening at the bottom. ...So my MeCreator gets lots of cooling air for the control PCB and...

This thing was made with Tinkercad. ... For the MeCreator 2, since the cooling fan of the electronic was pointing in a direction i couldn't use ;-) And its quieter now too !! ... (duck-tape is just temporary, testing if the cooling/sucking is enough)

( I use one for a skateboard from ABEC ;-) Print Settings Printer: MeCreator 2 Resolution: 0,2 Notes: I used Craftware 1.14 beta for slicing. 230 deg. nozzle temp. 85 deg. heatbed which means 65 deg. on the taped surface. ...infill : 20% Bottom part...

I was not satisfied with the stock fan shroud that came with the MeCreator 2. Even though it worked, the print quality was not very good and I didn't like the design in general. I decided to design my own fan shroud for it.  I designed this model...

I wanted feet for the MeCreator 2 because the Y axis is directly mounted to the steel chassis and is pretty heavy duty because it has to move the extruder and the X axis motor. And because I didn't find something like I wanted here on Thingiverse, I...

This is a bottom plate for Geeetech MeCreator 2. Since I was frustrating to have a noisy fan at the bottom of this printer, I have designed the bottom plate to be able to put any fans! ;) My printer became so quiet now with this design! :3 ...

3D touch holder for Mecreator 2 printer.

simple filament holder for MeCreator 2

MeCreator 2 Cover for X-axis (PCB) Print Settings Printer: MeCreator 2 Rafts: No Supports: Yes Resolution: 0,2 mm Infill: 20% Notes: Support is required for the rear clips. Post-Printing No postwork. ...How I Designed This 3D CAD Programm

Here is a GoPro monut that I designed using OnShape. ...This mount is designed to snap right onto the Geeetech Mecreator 2 3D Printer. ...The fit is very snug to ensure that there is no movement during printing.

Nozzle Fan Duct for the Geeetech MeCreator 2 Infill doesn't really matter as there is almost none to be filled. ...Fan used is a YS TECH BD125015MB 50x50x15mm 3pin connector I purchased it in Germany via Ebay ( http://www.ebay.de/itm/151888174887 )

This is a mount for the Chimera/Cyclops cooling/hotend on the MeCreator 2. It needs 2x M3 nuts and 2x M3 10mm screws for affix it. My set from china had large tolerance, so would block due to too little cooling with PLA. Added Copper Grease along...

me creator 2 axis replacement

simple anti-vibrations for MeCreator 2

Eine Autobed Leveling Sensor Halterung mit Lochdurchmesser 12mm für den MeCreator 2. ... Passender Sensor https://www.conrad.de/de/kapazitiver-naeherungsschalter-m12-buendig-pnp-pepperl-fuchs-cbb4-12gh60-e2-v1-156456.html

As you may know, the noise of MeCreator 2 is so loud. This thing "reduce" the sound coming from the case fan. ... <strong>Note: The noise will NOT be perfectly disappeared.</strong> Cutting cross bar will work much better :3 <strong>Updated:...

This is is a shim spacer, a hight-compensator if you want to use an additional glasplate on your MeCreator 2. With the leveling screws you are not able to compensate the height of the plate, so the Z-Axis-Endswitch has to be touched earlier. The...

Adapter baseplate and bracket to mount the MK8 Extruder of the MeCreator 2 directly to the genuine E3D V6 Hot End. Big thanks to http://www.thingiverse.com/thing:1895072 for the inspiration! Warning: Modifications to the MK8 Extruder are necessary,...

=> set your user and that should be it for this part ;0) ----------------------------------------------------------------------------------------------- Klipper ---------- From a terminal(or Putty), connect to your Raspberry Pi then: - Connect your...

You need 4 M3 screws an 2 M3 Nuts Print Settings Printer: MeCreator2 Rafts: No Supports: No Resolution: 0.2

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/bL9jZuHXokA

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3NW7MdPGva4

This is a remix of Spotz's Vibration damper! After printing his great damper with support material, I realized the support material inside the slot is almost impossible to remove... (Yes, you don't have to worry about this if you can manually set...

Remplace the rear simple lock cable. ... Just need a screw and a place more 2 tie cable nylon

Use with my tube, please. ... you can put pin cleaner into == Update version 2 More easy to print

I suggest PETG or ABS with 50% infill at least The right support only requires supports and brim or raft. Print Settings Printer: SKR 1.3 - A30 Rafts: YesSupports: Yes Resolution: 0.2Infill: 100 Filament: Variuos PETG White Category: 3D Printer...