meepo v3 controller 3d models
111809 3d models found related to meepo v3 controller.thingiverse
Thumb switch extension for the wowgo/meepo controller that is shared among a lot of cheap boards and DIY projects.
thingiverse
This is perfect for holding a Meepo V3 if you have hardboard walls. Depending on they type of hardboard you may need to use a little bit of glue to hold it in place. When saving, dimensions may be scaled down so you will need to convert inches into...
thingiverse
This is a custom-made deck protection/bumper I made for my Meepo V3 electric longboard. You don't need any screw or glue to mount it on the deck, the bumper self-stuck on your longboard and never get off! I also made a second bumper with the...
thingiverse
I always wanted to clean up my boards, so I drew this wallmount. The front wheels slide perfectly into the mounts and the boards hangs down secure. Make sure you check which charger mount you need (you can see the diffrence on one of the pictures),...
thingiverse
This version is stronger and has an option of a cross brace so the splash guards wont move if there is vibration.
grabcad
Microsquirt V3 EFI Controller http://www.useasydocs.com/index.html
thingiverse
# Fusion 360 Links Kleine Version: https://a360.co/2YXOny6 Große Version: https://a360.co/2Vc1avG # Controller Case for FHEM RGBWW Controllers V3 See also FHEM Forum: https://forum.fhem.de/index.php/topic,69740.msg612566.html # V3 Case Unten kann...
pinshape
A new Version of PS4 Controller stand. Check out thePreview!! ... and theTimeLapse video !!!
thingiverse
... it has an ATX power header to provide the power. This means power is not coming over the RS485 cable which has the side effect of reducing noise. Instructions Full instructions here: http://wiki.makerbot.com/thingomatic-doc:extruder-controller-3-6
thingiverse
It is a standalone or part of the 4 Controllers Stand The idea is to create 4 of these so 4 controllers can be kept on the table. Those stands should be stackable hence the locking at the back. Two plates (one on top and one on bottom) in the middle...
thingiverse
I didn't like the shape of existing thumb extenders so I made this one. You can attach it by putting a small drop of superglue in the hollow part, and then putting it on the upside down remote. ...It will avoid glue dripping in the internal...
cults3d
Attack! ...Where do you think you're going? Fans art of Dota hero Definitely a nice piece of art to be in your collections if you are also the fans of Dota Meepo. ... Have fun printing!
thingiverse
The HeliPlane for this controller can be found here,http://www.thingiverse.com/thing:1376182 Using a MindWave(EEG reader), Bluetooth to a smart device that, puts out an audio signal to an Arduino board, to turn a servo for printed parts, to rotate a...
myminifactory
These are simple bash guards designed for Meepo shredder trucks. ...The board used on this is the Meepo V3
thingiverse
Fenders used for the front wheels of a meepo hurricane, with meepos pneumatic cyclone racing wheels.
thingiverse
These are a pair of bash guards I designed for use with Meepo "Shredder" tracks. The board I based these guards off of is the V3. ...The holes go below the nut but above the actual truck, so they don't tilt the truck and impair handling/
thingiverse
Created this project to control LEDs with DMX-512 via WiFi with NodeMcu v3. ...A Rs485 module will be used in this project with a XLR plug to connect with the decoders. For more information: https://github.com/AGNworks/Controller-on-NodeMcu-v3
thingiverse
Meepo the dragon keeper from the 3e and 5e adventure The Sunless Citadel.
myminifactory
this a replacement part for a broken belt cover for the meepo hurricaen electric longboard.
thingiverse
This is a print to go around the Meepo v3 rear hub motors (90mm not 100), to be able to work with 105mm cloudwheels in the front. Print in tpu (i used overture black tpu with a hardness of 95) i might add more treads later on and maybe better...
thingiverse
This is an enclosure for the OpenBuilds xPro V3 motion controller. I am not affiliated with OpenBuilds, just a customer. The top plate (lid) slides on and has a cut out to accommodate an ATX style PSU. ...This was designed for my laser etcher build.
thingiverse
This little box holds the BGC V3.5 gimbal controller nice and snug and gives a flat plane on top and bottom for sticking it to whatever you need! it can be friction fit together or a dab of glue on either side if you want a more certain fit. ... ...
thingiverse
This is a Bash guard i made for my meepo V2 Just loosen the screws and put this between the board and vibrating damper.
cults3d
3D printed Hubs to work with Meepo Classic to use AT wheels Here is a video about them https://youtu.be/EeSmZWRPLPI
thingiverse
Just starting to make a case for this Meepo M4S Remote. Super Scratch I'll be back with updated models. ... Comment what you think so far...
thingiverse
... of the stand to better match the original xbox and ps4 files see the photo. Having printed this now a v4 could better hug the controller and have a front lip too to 'lock in' the controller, feel free to remix this further with this suggestion