mega bix 3d models
15755 3d models found related to mega bix.thingiverse
A replacement label rail for BIX telephone punch-down frames. ...I had a few frames at work that were missing label rails so I made this up and printed replacements.
thingiverse
This is a tool to insert ethernet wires into an BIX patch block. This is NOT a 110 tool. The print does not require support. The 100% infill print takes about 1.5 M of the 1.75mm filament. The tool worked fine with 20% infill. ...
thingiverse
The Bix 3 includes a laser cut FPV mount, but I still decided to make my own to fit my pan/tilt mounts linked below. CCD Pan Tilthttp://www.thingiverse.com/thing:592448 Fatshark 600tvl cmos Pan Tilthttp://www.thingiverse.com/thing:401461 I dont...
thingiverse
Scanned with The Scan-O-Tron 3000 (http://www.thingiverse.com/thing:127968), ReconstructMe (http://reconstructMe.net) and an Xbox Kinect at the Great Fredini's Coney Island Scan-A-Rama booth at the 2013 World Maker Faire New York. The Great...
thingiverse
Customized version of http://www.thingiverse.com/thing:1515242 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1515242 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:175150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=175150
thingiverse
Foldable 2.4ghz antenna mount to fit into the slots underneath the motor. Use M3 nylon screw to put arm & adaptor together. ...You might want to mirror Bix3_antenna_adapt.stl
thingiverse
Hello folks, I'm a backdrop builder with over 15 years of experience. You can see my work on my Instagram or Youtube channel. Thank you by following me or send me a tip. ... best regards Nerfi_Star See my Work: Instagram: NERFI_Star ...
thingiverse
Hello folks, I'm a backdrop builder with over 15 years of experience. You can see my work on my Instagram or Youtube channel. Thank you by following me or send me a tip. ... best regards Nerfi_Star See my Work: Instagram: NERFI_Star ...
thingiverse
This design is for those wo are fed up with the original motor mount which is a joke regarding accessibility and serviceability. Use this design if you want to change the motor easily, even on the field. ... - 4 screws fastening with washers -...
thingiverse
Hello folks, I'm a backdrop builder with over 15 years of experience. You can see my work on my Instagram or Youtube channel. Thank you by following me or send me a tip. ... best regards Nerfi_Star See my Work: Instagram: NERFI_Star ...
thingiverse
For mounting board cameras securely onto the plywood FPV pod that comes with the Bix3. 30min Epoxy and 4 M2 nylon screws/nuts/spacers are needed. ...
sketchfab
VR logo for our indie game Super Mega Mega This model was made with Qubicle. ...www.GetQubicle.com
thingiverse
Custom holder for the l9r frsky reciever to suit the bixler 3 Print Settings Printer Brand: Up! Printer: Up Mini ...
thingiverse
I have remixed the FPV tray (made by @FreeFlight) and added a built in Gopro mount. Printed in PLA and tested in flight. Ultra strong, no problem to hold my Hero 7. ... In order to be complete the tray needs also the back end...
thingiverse
I looked at a bunch of motor mounts for the Bixler 3 & liked the simplicity of this one & the fact that the motor can be easily swapped out. I modified it slightly to use all M3 hardware (rather than M4 hardware to join the two parts like the...