meteor mic stand 3d models

Meteor Fighter The Meteor is a heavy aircraft build around a large bore main gun to be used against Mechs and tanks, but can allso be fired at other Aircraft!Skilled pilots can achive great things with this Fighter, but most newer pilots find it...

This is a simple spheric M4 nut holder as a replacement part for the K&M Mic stand.V1 worked great for me with a 4.5mm drill afterwards.V2 the hole diameter is set to 5mm.

A practical and convenient holder is now available to secure a 5/8" mic stand, making it easy to organize cables and two picks in one simple print. ...Share your creations with us!

This is a universal pick tray conversion for any clamp-on mic stand cup holder, specifically the B001D2TPZU model available on Amazon. ...The standard base measures 75mm in diameter and can likely accommodate various other models of cup holders.

Meteor hammer for practice.Rope Dart version.If you are only printing the hammer, be sure to put the model approximately 5mm above the build plate to avoid ugly flat surfaces.The weighted version has space inside to insert 3/8" hexagonal nuts. ...Be...

The SS Meteor whaleback laker is situated in Superior, WI. A photo set was captured using a Mavic Air 2 in 4K movie mode. The footage consists of one pass around the side of the ship and then over the top. ...My 3D asset was generated with...

Use cable ties to secure the clamp on the mic stand. One should suffice, but you can also use two if needed. I opted for the larger ones. The mic-stand diameter is 15mm. This setup works just as well with a larger diameter, up to 20mm. Have fun...

The Meteor Starship is storming to a table near you!=FDM ZERO SUPPORT PRINTING= -TWO CONFIGURATIONS-Because one mode was not enough this ship comes with two configurations. The first configuration being the ship on its side, including a custom gantry...

Hey, Get your Meteor to blast away anything on the Fortnite map, or annihilate Tilted Towers. Map: https://www.thingiverse.com/thing:2841194 Tilted Towers: https://www.thingiverse.com/thing:2842223 If you have any questions, comments, or concerns,...

So, I searched for the puzzles on Onshape and found a Meteor Madness design by Tom Koster. I edited the original design and printed it, and was quite pleased with the puzzle. The puzzle turned out so well I decided to share it here. I split all...

Meteor Crater https://en.wikipedia.org/wiki/Meteor\_Crater Print instructionsCategory: Physics & Astronomy How I Designed This...

Meteor Crater is a massive hole in the ground located in Arizona, USA. The crater was formed around 50,000 years ago when a meteorite estimated to be about 150 feet in diameter and weighing several hundred tons struck the Earth's surface with...

I was unimpressed by the variety of things on Thingiverse, so I created my own instead: This piece of plastic printed in PETG converts the 5/8" 27tpi thread of mic stands into a 20mm diameter cylinder. Simply drill a 20mm hole into some wood and set...

This is a quick adapter I made that lets you use the Denon AVR cardboard mic Stand for the UMIK-1. The finished print should fit the UMIK-1 snugly, but not too tight. Scale down or up 1% to desired tightness. ...This can be made with either PLA or PETG.

Remix of original Mic Stand Camera Adapter modified to capture the 1/4 -20 bolt head instead of relying on glue. If you appreciate it, please show your support for the original creator. ... Remixed from this design:...

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion 360...

The 5/8"-27 nut or microphone holder should be on the side facing you and screw on to secure the adapter to the mic stand To use this, you will need: - 3d printed mount by defucilis - 2 M4-0.7 x 25 mm screws - 2 M4-0.7 nuts (wing nut or hex nut will...

It appears you've shared a complex 3D modeling project for a Zen Meteor rifle scope from the game Destiny. The post highlights several challenges associated with building this item, including its size, length, and assembly requirements. Here are...

This is a replacement part for the Blue Snowball mic stand. Factory plastic parts on the legs are subjected to considerable pressure, making them prone to breaking. To create this part, simply print with an infill of about 35-40%. No supports are...

This is remix of holder for C-1U mic stand previously remixed by CapObvious. I've had problem with the treaded part which kept broking for me from PLA. So I've made it non moveable. This is a remix from https://www.thingiverse.com/thing:398515...

I designed this mic stand for my nephew, who had a shock mount and microphone but was missing one crucial piece: a sturdy base to hold them in place. The design includes a limited rotational feature, allowing for easy adjustments without compromising...

... my custom solution, I utilized the nut and bolt from an off-the-shelf microphone holder. Alternatively, users can opt to use the base of a store-bought mic holder instead of printing their own, although this might result in a slightly smaller fit.

I created this custom solution because my mic boom stand wasn't compatible with the adapters I had, forcing the tablet screen to face the wrong direction. To fix this issue, I designed a makeshift adapter that allows me to view the tablet screen at...

Just pick your can (12 oz or 16 oz), print the base and top and now you the perfect face-level mic stand for any mic with 5/8 inch threading. ## **Printing** Infill: 100% recommended. Walls are only 2mm thick and you want good infill on the...

More about that here: https://mbz4.blogspot.com/2021/06/auna-usb-mic-stand.html The version in the attached images is a prototype variant and differs from the .stl file uploaded here: the version I included for you features a convenient cable slit...

... It is [posted there as MC_60_V9. I originally had my callsign embossed, but this version is a bit larger with the mic a little more forward and "KENWOOD" is now embossed on both sides. ... https://www.tinkercad.com/things/hqrKXc1abLP

This is a foot for my mi-u2 aukey condenser mic that allows it to slip under a desk pad and sit a little shorter so that it slips under my monditor. ... I know this is kind of a niche, but maybe someone else out there has the same need.

The radio and microphone stay locked in place using the grooved on the back side of the model, preventing them from moving around when you pick up the mic. I made this with the stock UV-5R and the Baofeng UV-5R mic, so it has not been tested with...

I've created a version of the flange that enables direct screwing onto the metal support, making it easy to use your mic while on the move. I tested this feature today in the field, and it's incredibly convenient. To ensure optimal results, I...

Simple 1" ball end to microphone stand (3/8 inch with 16 TPI) adapter. ...I made this to attach my Ram X-Grip phone/tablet mount to a boom microphone stand. ...For added grip, you can add plastidip to the ball end.