meteor mic stand 3d models

GE DV1 Mic Duct blocks unwanted wind noise effectively, although it may not always be completely successful. Print settings are available below. ... Print Settings Rafts: Enabled Supports: Disabled Resolution: Set to 0.2mm

I removed the aftermarket mic from it's housing and place it within this bracket then placed the bracket in the factory location. The hole for the mic ended up being slightly small but a little heat from a lighter allowed it slide in. I printed...

I've had great success using a Zoom H1 (available on Amazon) when the field of view is set to Narrow, or a Rode VideoMicro Compact Mic with the GoPro still set to Wide. ...My idea was inspired by this innovative product: Polsen GPMK-22 GoPro Stereo...

I didn't have a drum mic, so I decided to mic up the drums by creating this mount and printing out three pieces. Then, I took three Sennheiser e835 microphones to cover the snare and two toms. So far, they're working perfectly and staying in place on...

I removed the aftermarket mic from it's housing and place it within this bracket then placed the bracket in the factory location. The hole for the mic ended up being slightly small but a little heat from a lighter allowed it slide in. I printed...

... a lo-fi mic, this setup is ideal for experimenting with unique audio effects. The addition of a switch allows users to seamlessly transition between the two different mics, while a miniature arcade button enables them to bridge the signal with ease.

I had to whip up a makeshift boom mic on set without breaking the bank, so I cobbled together a simple connector using a hot shoe for a microphone and a trusty broomstick. By threading an M5 nut and bolt through the joint, I was able to secure the...

Case for the ReSpeaker 6 Mic Array - A Comprehensive Solution Upgrade your audio experience with this premium case designed specifically for the ReSpeaker 6 Mic Array. This robust and durable enclosure provides a secure fit, shielding your device...

I've provided mounts for 35mm and 32mm poles (hopefully fits most monitor poles) and it will fit any mic that uses the standard 5/8" mic screw. Each hinge has adjustable tension so it will all stay where you put it.What you'll need:608 Bearings -...

It's designed to convert a single 5/8 inch adapter for a mic into a stereo 5/8 inch adapter for a mic. I highly recommend printing with 100% infill since it can easily break apart if not printed strong enough. However, 25% infill seems sufficient...

It comes with a red clip that allows the mic to be attached to the flash slot of the DSLR camera, allowing easy recording while moving about. I broke that clip while removing the mic from it. These are 2 different kinds of clips that I designed to...

Wire can be route in the slots, I used blu tack and sewing thread to held it in place, loop the mic wire in the side swivel joint. The mic holder connector to the side swivel arm is 5.2mm diameter if you wish to make your own mic holder. ...

The mic holder connector attaches to the side swivel arm with a 5.2mm diameter; if you prefer to create your own mic holder, this information will come in handy. ... Update: May 16, 2018 A desk clamp attachment has been added: - The desk clamp and...

... the bracket in the factory location. The hole for the mic ended up being slightly small but a little heat from a lighter allowed it slide in.I printed with pla, no top or bottom layers and 30% honeycomb infill.This was for a 2010 Toyota Seqoiua

To attach it to a tripod, use a 1/4 inch nut (secured in place with super glue) and rubber bands to hold the mic firmly in position. A complete set requires one base and two rings. ...I personally use solvent weld for assembly, but you may also be able...

* Bendable design * 19mm opening * 1mm extrusion on the bottom which clips into the groove on the microphone, locking it in place * Front face chamfered for easier insertion * Screws onto the base of a regular mic clip. Pictures are PLA printed...

I wanted to mount a Radioddity RS22 mic in our UTV, but it comes with a belt clip, which kind of makes it hard to put it somewhere handy. The mic clip stl replaces the belt clip, making use of the existing screws. The clip fits the holder (which is...

... the board without too big of a holder. I've used the universal hooks and printed the holder without supports. After I took the pictures, I've reduced the grip distance for the mic slightly (5mm vs 6mm) because the microphone was held a bit loose.

Three part Stormtrooper HOVI Mic Tip greeble for an Original Trilogy Stormtrooper Helmet. Higher resolution prints yield far superior results in terms of detail on the printed piece. It's highly recommended to use rafts and supports, along with some...

use with Wireless/wire Microphone,i am usint it with my drone "dij air 3" the link for the mic: https://www.aliexpress.com/item/1005005086707138.html?spm=a2g0o.order_list.order_list_main.40.1d711802z2R6Dzi am using a round magnet 15*2mmThis object...

... centered around the notion that if I were to personify Matt as an object on a desk, it would likely take the form of a microphone. ...This thought led me to design a mic specifically tailored for incorporation into a streamer's or videographer's setup.

This Mic Clip is specifically engineered for wireless microphones within the Sennheiser EW series. It's designed as an external attachment that can be securely fastened to a wrist or arm. ... I highly recommend utilizing a flexible PLA filament, printed...

Summary This mount secures the tiny shotgun mic firmly onto a monitor while offering flexible positioning via a ball and socket pivot, ensuring clear sound quality through a 3.5-inch audio pigtail that reduces noise and provides strain relief. ... ...

I created this mount specifically for 3D printing, designed to securely attach a Rode NTG2 shotgun microphone or a similar mic to a camera cage. ...The design process was handled with Tinkercad, and you can edit it online at...

... in ABS Plastic that works with RAM mounts or any 1" ball mounting system. ...It is easy to install and remove as well as being strong so the mic doesn't pop out on super bumpy roads. ... I included the SketchUp file so you can edit it if you'd like.

Razer Megalodon gaming microphone features a unique mic plate design, boasting a precisely crafted 25.5mm slot positioned at its center. ...This thoughtful innovation allows users to seamlessly install an LED board, all while avoiding the need to...

... this for an escape room our library is developing. ...The peg fits into a mic jack for part of the puzzle, and the top holds a QR code insert.\r\n\r\nThis design was made with Tinkercad. ...Edit it online at https://www.tinkercad.com/things/gQT5uVhnbxW

This was created in an effort to fool-proof lapel mic positioning on the speaker. This was made for an Audio Technica AT829cW microphone. Even after repeated explanations people still failed to realize which side the sound went into. ...Hopefully this...

I designed a handy boom hook that makes it simple to suspend my headphones from the mic boom arm. ...The clearance required for the boom itself measures precisely 2.05 millimeters, while the width of the hook attachment is 36 millimeters.

An adapter designed for use with Rode Boom Mic (Videomic) is available. It attaches to the microphone's shock mount and fits precisely onto the Rode Directional Video Condenser Microphone. ...The boom's tight tolerance allows it to thread securely,...