microcentrifuge eppendorf 3d models
295 3d models found related to microcentrifuge eppendorf.thingiverse
The outer diameter of 1.5mL Eppendorf microcentrifuge tubes is approximately 10.9mm by my measurements. However, when printing with a 0.8mm nozzle, I had to design the holes as large as 12.2mm for the eppendorf tubes to fit easily. I have not...
thingiverse
... ...For use with 1.5mL Eppendorf tubes. Similar to those found online. Significantly cheaper to make them with a 3D printer instead of buying them. Print with no supports if doing the one with built in ones. ...Should print out just fine at 20-40 %infil
thingiverse
I needed to vortex 20+ Eppi tubes at once for some biology experiments. This thing lets me do that! ... Only other part required is a small length of ~8mm rod (could probably get away with printing it).
thingiverse
I've designed this piece for my pipetting robot and I thought it might be useful for someone else. It has been designed to store solution at 4°C in microfuge tubes if you manage to print or build it in aluminium for example. The carrier respects the...
thingiverse
I designed stand for 4 oder 8 times 1.5 mL Eppendorf tubes and want to share them with you. ... Others can be designed and uploaded on request.
thingiverse
I designed stand for one 1.5 mL Eppendorf tube and one for a 15 mL centrifuge / falcon tubes to be placed on a scale to weigh in a sample and want to share them with you.
thingiverse
This is a simple rack for 15 microcentrifuge/Eppendorf 1.0-1.5ml tubes. If you want to store the tubes in a sealed container in the fridge or freezer, this rack fits the 6.76 oz/200ml Sistema plastic containers, and holds the tubes upright. ...The...
thingiverse
Here is a simple holder for a 1.5 ml or 2 ml microcentrifuge (‘Eppendorf’) tube, as part of my 3d printing labware range. ...The goal was to make items which: - Are functional (in this case securely holding tubes upright) - Use minimal plastic, and so...
thingiverse
Simple rotor, for holding 1.5-2mL eppendorf microcentrifuge tubes. It will fit onto the spindle of a standard 3.5 inch hard disk drive. The spindle mounting hole is slightly undersized. This is by design, you'll have to sand it out until you get a...
thingiverse
This is an adapter insert for a microcentrifuge for 200uL PCR tubes. ... It Should be printed on a SLA printer if possible. It should be able to withstand up to 2000g force (max. on presented Cole-Palmer microcentrifuge). ...
cults3d
This is an adapter insert for a microcentrifuge for 200uL PCR tubes. ... It Should be printed on a SLA printer if possible. It should be able to withstand up to 2000g force (max. on presented Cole-Palmer microcentrifuge).
thingiverse
This is a microcentrifuge rack that holds 0.7mm tubes. Can be used in laboratory environments where not many have a rack which can support those tiny tubes. ...
thingiverse
Larger than normal size microtube rack for all of your biology needs! ...Fits most standard sized microcentrifuge tubes with plenty of room in between tubes.
thingiverse
This is a small rack for 1.5 ml microcentrifuge tubes (11 mm diameter). 20 tubes can be stored in the rack. ... The rack consists of four different parts which have to be put together and can be secured with two M3 nuts and two M3x16 screws if...
youmagine
The source file is provided for you to change the shaft diameter or tube size if necessary.This rotor was designed to be used in the RWXBioFuge, an Open Source table-top microcentrifuge, fully documented on...
thingiverse
This is a simple rack to hold four 1.5 or 2.0 ml microcentrifuge tubes. Tubes from different manufacturers should be more or less the same size, and the few brands I've tried have fit fine. ... ...
youmagine
Link to publication:http://pubs.acs.org/doi/abs/10.1021/acsomega.7b01310 This particular part is meant to allow reproducible analysis of samples held in a micro-centrifuge tube (VWR Microcentrifuge, Cat No. 20170-333). This adapter can be used in...
thingiverse
Link to publication: http://pubs.acs.org/doi/abs/10.1021/acsomega.7b01310 This particular part is meant to allow reproducible analysis of samples held in a micro-centrifuge tube (VWR Microcentrifuge, Cat No. 20170-333). This adapter can be used in...
thingiverse
The Orbiter Micro is a super portable mini-microcentrifuge that fits on the palm of your hand! It is designed with a fully 3d-printed body and rotor... no bolts and nuts needed. It runs on either battery or DC power plug... so you can take it almost...
thingiverse
Two versions (20 tube and 32 tube) of a simple eppendorf tube holder/rack. Obviously, print with the flat part down. ...Holes should be spaced far enough apart so you can fill each hole and still have a little space between tubes.
thingiverse
This is a StageTip Adaptor for microcentrifuge tube for stagetip made with peptide tips. It provides more secure holding of the StageTip in the eppi tube so it can be span at a higher speed to shorten washing and elution step. ... Gcode included to be...
thingiverse
I designed this box to put my Eppendorf tubes in during incubation, this allows me to lie the tube on its side in the shaker without the worry of the tube popping open. Can print without supports if oriented in the correct way. ... I currently...
cults3d
Eppendorf pipette design with lid Eppendorf pipette design with cap