microphone mount adapter 3d models
444373 3d models found related to microphone mount adapter.thingiverse
I made this to adapt an Audio-Technica ATR2100 microphone (30mm barrel) to a 50mm isolation mount. ...
thingiverse
This is an adapter that allows the Blue Yeti to fit in a smaller microphone shock mount, in this case this one: https://www.aliexpress.com/item/32970506807.html Use electrical tape to make everything stable and use an angle micro usb cable to connect...
thingiverse
When using a Blue Yeti microphone with a generic microphone arm, the adjustment knob hits the mini USB connector. This extension allows the knob to clear the cable. Threaded to 5/8-27 TPI on the mic end and 3/8-16 on the stand end. More than strong...
thingiverse
[ENG] An easy way to attach a microphone arm, [like this one](https://www.amazon.com/dp/B08RCYW528/ref=sr_1_28?keywords=microphone+arm&qid=1641992764&sr=8-28 "like this one"), to a monitor mount [like this...
thingiverse
Microphone Cold Shoe Adapter Specifically designed to mount a Rode Wireless Go / Wireless Go II microphone to a microphone body with a 30 inch diameter but can be used to mount any cold shoe device to a microphone. Included F3D file so that you...
thingiverse
Again, nothing too fancy. ...Screw that ****er into your mic mount, connect the GoPro-style mount to the rest of your modular mounting system and boom.
thingiverse
Adapter block that screws onto the end of a boom pole or any other standard microphone mount with 5/8"-27 threads. It gives you two cold shoe mounts. It's useful to mount equipment such as microphones and recorders that were designed to mount onto a...
prusaprinters
Adapter block that screws onto the end of a boom pole or any other standard microphone mount with 5/8"-27 threads. It gives you two cold shoe mounts. It's useful to mount equipment such as microphones and recorders that were designed to mount onto a...
thingiverse
Microphone shock mount adapter to mount it on camera tripod. (You will have to drill hole and cut thread for tripod!) UNEF 5/8" (USA/Canada - Extra Feingewinde) Außendurchmesser: 15,875 Steigung (Gänge/Zoll): 24 Steigung /mm: 1.0583...
thingiverse
This is a M6 adapter to fit a camcorder or camera onto a standard microphone 15mm screw stand.Use two appropriate washers for each side of horizontal bolt to prevent crushing the 3d print.I made this because i had a few mic stands lying around and...
thingiverse
I bought a LED ring with a table tripod, but I wanted to place it on a microphone stand that I had for better lightning. I've been searching here for this kind of adapter and I didn't find any, so I've designed my own, based on a couple of other...
thingiverse
Adapter for the modular mounting system I suggest very fine printing because the thread is very fine. ...Also plenty infill cuz microhpne usually are heavy.
thingiverse
Screw adapter to attach a microphone clip to a standard camera mount e.g. ...on a tripod.
thingiverse
This threads into a microphone and allows a 1/4-inch camera or speaker mount to hold it. The design from groundwater wouldn't thread into my Snowball microphone, so I drew my own in Fusion 360. The nice thing about Fusion 360 is that I can create...
thingiverse
An adapter to mount a 5/8" microphone mount to a cheap flexible tablet arm. Working with an anti-shock mount came with BM-800 mic and a stand from few years ago lying around. Adjustments might be necessary to suit yours if it isn't exactly the same...
thingiverse
Print the screw at 100% infill and 0.1mm layer height for good results. You can use the InfillMesh.stl to set different infills for your screw and your body (not to have to print the whole body at 100% infill). ... This is a remix using...
thingiverse
Mount to attach a microphone shock mount on an Anycubic Predator. Thread is a standard 5/8 - 27. This setup helps to keep the pump quiet. The original screw can be reuse. Must be printed with a filament having a good layer adhesion like...
thingiverse
I needed a shock mount for my second hand Behringer C-1U and what I found wasn't printable in my Voladd, so I did my own design.
thingiverse
Adapter for a Microphone (Rode), but I think it's possible to mount other microphones or lamps on this clamp for DJI Osmo Mobile 3.
thingiverse
An adapter to mount a pop filter in front of a Samson Meteor Microphone.The thread is quite fine so I recommend printing at .2mm or lower.
thingiverse
Mic shock mount adapter to connect to old IKEA lamp. UNEF 5/8" (USA/Canada - Extra Feingewinde) Außendurchmesser: 15,875 Steigung (Gänge/Zoll): 24 Steigung /mm: 1.0583 step_shape_degrees = 30 nach ISO262...
thingiverse
I just needed an adapter for a microphone stand, it turned out pretty good, I guess the thread could have been a little deeper though. ... Printed it at 65% infill but you could probably do less
thingiverse
Microphone mount for my BM-800. You need m4 screw. ...Print Settings Printer: p3Steel Rafts: Doesn't Matter ...
prusaprinters
Microphone mount for my BM-800. You need m4 screw. Print instructionsCategory: Audio Print Settings Printer: p3Steel Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.3 Infill: 30
thingiverse
... whacked him into things or off the desk. This was inspired by various other headphone desk mounts, of which I also use. Yes it's ugly, but it's my most useful print and possibly my proudest print to date in terms of functionality. ...
thingiverse
# Microphone to camera screw adapter ------------ This adapter allows to screw a microphone mount onto a common camera thread. ... (3/8 - 16 UNC to 1/4 - 20 UNC)
cults3d
Universal microphone handheld adapter and extension. ...5/8"-24 UNEF thread both top and bottom, so you can use it to hold a microphone whilst speaking, or for a little more height on a mount or tripod.
thingiverse
Microphone stand adapter to convert standard mic holder to one to support larger style, cordless microphones (35-37mm) diameter.