microsd extender 3d models

Just a small extender pole to fit on the original. Follow original steps. If the holes are a little lose, tape together or a dab of superglue. The taller the stake the less robust it is, but i found adding one or two with some tape still gave plenty...

This is a simple design I created to extend the height for my Ikea desk. it will raise the desk 1.5 inches, or 38 mm. The fit is around the desk legs was purposely a bit larger to allow for any slight variations there might be with Ikea desk...

This remix imporoves upon turtlecreations design by further extending the height of the polybox, thus allowing for more sophisticated bearing solutions. It also adds support structures to ensure the lid does not bow inwards, thus making the enclosure...

This innovative cup holder extender provides an extra spot for your drinks, fitting securely into your existing cup holder via a pipe expansion mechanism. With two of these devices, you can have four cup holders at your disposal; why not outfit every...

This is a lifter or extender for standard size can dispensers. These dispensers are supposed to be stackable but they don't stay connected or stable. I also noticed that if you lift the top one just 35mm, you can put a second row of cans in the...

This is a remix of the Cup Holder Extender With Phone Mount by XKilox95. The only change was to remove the phone holder. Since the model was designed to work with LTT water bottles I also included a model with the LTT logo on the inside. ...It will...

I figured this could be solved by simply extending the arm which worked like a charm. The extender fits right over the arm and has a flexible clip that hooks into the hole in the arm. This prevent the extender from sliding off over time. ...To...

2023-08-07: Did some refinements on the extender, the old design could sometimes fold up and get stuck in the tire when doing things like riding down stairs or jumping so I made it a little bit longer, changed the angle a bit and added a small...

This is a door latch extender that allows you to open doors but not let them fully swing open. The purpose of this device could be to keep pets out of certain areas, such as laundry rooms where cat litter boxes are located. Perhaps you have a dog...

Nerf stock extender made specifically for the Nerf Rapidstrike Stock with Battery Compartment made by tungstenexe but it should fit any standard nerf stock attachment.This extends the stock with 10cm.I added both necessary files from the original...

I got a sheath with elastic on the sides, but I don't trust that my bit extender wont slide out as the elastic gets worn in. There are 3 ribs to fit into the 3 grooves on the end of the bit extender. I made it 2 pieces so neither piece is weak along...

Just slip the end of the collar between the grippy parts and make sure the hole lines up with the détente before latching the other end of the extender through the buckle. After just one redesign, it worked out quite nicely, I must say. If you...

I designed this vent redirector and extender because I was unhappy with the commercial options available for a long extender. I had to divide it up into 6 sections. I was not happy with the results when I glued them together, likely due to uneven...

I designed this battery tube extender from scratch for my ARP airsoft replica using DesignSpark Mechanical. The extender does not "clip" to the main body, but the stock will secure it in place and you can clip the OEM battery cap onto the back. If...

... magnets can be hot-glued into place. Additionally, a tiny mark was added to the top of the model indicating the correct orientation for inserting the microSD card so it won't be inserted backwards or upside down. ... It now works perfectly.

So I moved microSD card positions closer to the outside edges, so that "Microsd fit margin" can be set to under 0.15 without creating an outside lip and preventing microSD card insertion. Don't get your cards stuck! For the first few times insert...

... but I also wanted some slots to hold MicroSD cards. ...So I created this remix which replaces two of the SD card slot with 6 MicroSD card slots.I tried my best to keep the same design style from the original and apply it to the new MicroSD slots.

I'm designing a compact pixel extender box, a small printed circuit board (PCB) that outputs signals. The original design was created using "The Ultimate Box Maker" software, with parts sourced from Thingiverse and imported into FreeCad. To...

Luckily, there's a simple design that extends this exhaust port while maintaining a tight seal. This design is meant for printing on semi-flexible filaments like Sainsmart TPU. Because you need to stretch the filament over the port to get a good...

For some unknown reason, my heat bed cables kept getting snagged on the camera, so I simply created a sturdy extended arm mount using parts from his brilliant design. It was just enough to clear it out of the way and gives it a perfect angle on the...

Tony D crafts exceptional items, including his impressive KillStix attachments that fit snugly onto the Xbox One controller; however, it struck me as more of a decorative accessory rather than a practical extender. Convinced I could do better, I...

Fresnel lens flash extender 95mmx135mm Fresnel lens Fits SB-600 and Neewer 750II Please let me know what flash you use and how it fits so I can adjust accordingly. Print Settings Printer Brand: RepRap Printer: Prusa I3 Resolution: Whatever Infill: ...

I'm searching for a toilet roll extender that fits mega rolls and discovered they're charging $10 for these items. After browsing around, I couldn't find any alternatives that suited my needs so I decided to make one myself. This DIY solution works...

That's why I designed these extenders for the rubber feet in order to elevate the printer by 28mm so as to no longer squish my routed cables.To assemble, use one M3 nut and one M3x20 countersunk screw to secure the latch to the body, then insert the...

This was created to help extend a SimpliSafe doorbell out past brick that directly surrounds a doorframe. Mount was created to fasten doorbell backplate to mount using #6 screws and hex nuts. Update - Added an updated version which puts the mount...

howeveer after building it we noticed the height was really bad to work at. These feet extend the working height by 100mmThe model can be printed without supports.You might need a brim depending on your...

I had a need for an extra long light switch extender. I remixed bingbingaling's thing to make a two piece version. The two pieces are each shorter than the one-piece version so they should print on a smaller build plate if needed. I sliced this...

... 4-5 small wind turbines on the front grill, harnessing kinetic energy from motion to charge the battery via linked generators. This innovation would extend battery life while driving, enhancing long-distance travel capabilities in electric cars.

On the hive bottoms with 10 Nicot frames, I've extended the take-off board because it was too short - by a full 100mm. I'm using a flight plank that's just 5 mm thick. My proposal is to develop models for planks of thicknesses ranging from 5 to 20...

To upgrade my drone to perfection, I realized that simply extending my thumb sticks would be a straightforward process requiring minimal effort. Its design is centered around a Ø15mm thumb stick with a 12mm radius, making it compatible with any...