mini arduino pro 3d models

... shown here is an affordable import that fits perfectly, its 16.1mm diameter inserting snugly into place and secured by three M3 screws with nut inserts. I printed this in ABS using a 0.35mm nozzle. My Rostock Mini Pro should be up and running soon.

I've been experimenting with replacing the standard shroud on my Mini Pro at our local maker space with a part that closely resembles the original, and after some trial and error, I've finally found one that fits the bill. ...This new shroud is still...

This will fit the Wemos D1 Mini Pro / Relay Shield with headers mounted in the configuration in the pictures. Left a small hole to get to the reset button with a paperclip. Added a few ventilation holes in the back. Widened the opening for the...

The file I found on Thingiverse only hold on to the edges of the Atem Mini Pro because my monitor else wouldn't fit. Made some little changes for my needs. ... This is a remix op a remix ;-) Original design:...

Speedway Mini 4 (Pro) mudguard. Openscad (v. > 2017 - nightly build ok). This part can be split in two for printing purposes to avoid possible vertical drops. In this configuration, the two parts need to be assembled: drilling, rod (carbon,...

This allows you to mount a d1 mini pro (or clone) in an outdoor rated electrical box in one of the unused 3/4" holes. In order to maintain water-tightness, you must still use the plug behind the printed mount. I print the screw mount threads down...

The iPad Mini Pro has a unique extension system for added convenience. Check out my other extension holder, which is designed for a 30mm tube (like your tripod). For more details, visit Thinkercad at...

A Universal Mount for Mini Tablets like iPad or 7" Screens on Mavic Pro Drones. Utilizing Affordable Cup Holder Mounts Available Everywhere. Printing Details: Easy to Print, No Raft Required, With Minimal Supports Needed. Assembly...

The Mp Select Mini V3/Pro comes equipped with an auto-leveling probe, but it's not the only upgrade available for this 3D printer. The stock 30mm fan is not sufficient to cool down the hot end or the printed parts effectively. ...To address this issue,...

might share more mini 4 pro stuff soon.both legs are the same.brace 8 is ok if you just leave the landing gear on all the time or want minimal materialbrace 9 is 0.2mm thicker and has 0.5mm longer fingers. this one should be used if you take the gear...

This is a wire termination system (solderless) using pin headers in PCBs. (The rubber band holds wires in place.) If you want to customize it for your needs, please visit this updated version: http://www.thingiverse.com/thing:1381358). Print Settings...

Similar to BadUSB but with a header and for another use.

I flexed the wire segment an additional 0.2 inches.

Based on these projects: Rostock Mini Pro (CZAR) thingiverse, Rostock Mini (bwevans) thingiverse, and Rostock (Johann) thingiverse/github. Used Software: OpenSCAD 2015.10.17, Inkscape 0.91. Improvements in comparison to the Mini Pro: Revised...

Fully Adjustable Camera and Light Mount For Z-Pro IIIP Select Mini X-Support Attachment. -SD Card Reader Mount -XSE Toolholder PREREQUISITE MODELS Z-Pro https://www.thingiverse.com/thing:2797935 Ultra_Max Tool Holder Kit...

The first ones haven't been tested yet, but there's a simple hold-down bracket for both left and right sides of the ATEM mini (and the ATEM Mini PRO, since they share the same case). There's also an 80mm fan mount for either side, depending on where...

Direct Mount-On Stylist Holder Designed Specifically for the MP Select Mini Pro Printer. The Touchscreen Interface Makes It Easy to Operate, and I Protect It with a Nintendo DS Stylist Attachment to Prevent Damage and Keep it Clean. The hole is...

Designed specifically for iPad Pro 12.9 tablets, Generation 3 and 4 models are supported; however, compatibility with other tablet devices is also possible. Created as a car mount for larger tablets that can be printed using compact printers such as...

Inserting and removing the micro SD card on the DJI Mini 3 Pro can be somewhat difficult, since it sits fairly deep in the slot. Basically, a fairly long fingernail or some other kind of flat thin object is needed to insert and remove the card, but...

This license plate holder is designed specifically for mounting on the steering bar of the Ninebot Mini Pro Street scooter. Its compact size makes it ideal for a range of applications. Two additional cable ties and at least four M6 screws are...

The dji mini 3 Pro is an awesome camera drone and the RC controller is excellent. The controller has configurable buttons on the back (C1 and C2). Thes are useful for resetting the gimbal or changing the filming mode. The only trouble is that the...

This mount for the 8mm EZABL Pro Mini is designed to be as stiff as possible in order to eliminate any deflection while probing. The first version I designed hung lower and attached closer to the tip of the probe which made the mount easier to...

A set of wheels made for the Mini JRX2 that replicate the Original JRX Pro dished wheels with the "TEAM LOSI" lettering. Not a perfect replica but a nod to the originals. These wheels have more reinforcements spokes than the original style wheels...

This build accommodates the Wemos D1 Mini Pro / Relay Shield with headers installed in the configuration shown in the images. A small hole was left to access the reset button with a paperclip. Several ventilation holes were added to the back for...

Protective cover for DJI Mini 3 Pro battery This battery has very thin walls and should have contacts covered in storage or when travelling. Simple cover that provides snug fit for battery and holds the stock snapping tabs. Two files provided: * ...

This case is for the DJI Mini 4 Pro and the DJI RC-2 controller. I considered designing an all-in-one case (like I did for the Mini 2 https://www.thingiverse.com/thing:5149277), but there wasn't an efficient way to align the drone and controller, and...

This new version includes files for both "Wemos D1 mini" and "Wemos D1 mini pro." I've also designed two separate lids, one with a closed top and another that features an opening specifically for the Wemos OLED 0.96" shield. There are several...

This is a second version of my previous Wemos boxes (https://www.thingiverse.com/thing:1995963). I have made files for "Wemos D1 mini" and "Wemos D1 mini pro". I also made two lids, one closed and one with an opening for the Wemos OLED 0.96" shield...

Ein griff für die GoPRo und Mini