rear enders 3 3d models
804831 3d models found related to rear enders 3.thingiverse
This is something that I threw together real quick, Its a rear plug for the power supply of the ender 3. I designed this as I have my power supply mounted underneath the frame to keep my center of gravity lower, and I didn't want to have to buy a new...
thingiverse
I designed this mount to better align with the Y axis chain on the Ender 3 V2. It is also a little more robust. It uses the angled heated bed mount found here: https://www.thingiverse.com/thing:3285566 It uses the z axis mount and slim chain...
thingiverse
The box slides onto the 4040 aluminum extrusion in the rear. Hardware needed: Screws to bolt it onto the aluminum extrusion. I think they're M5 screws? You can find them on the front of the same 4040 aluminum extrusions. ... 4x PC fan screws to...
thingiverse
Hi everyone, I designed this project to remove the motherboard from the front and put it in the back together with my raspberry pi4 and relay. Of course both board are equipped with two 40 mm noctua for cooling. Everything has been designed with...
cults3d
I made the model to adapt it to the ender 3 or pro. ...not for the ender v2
prusaprinters
This is my design for a case for the mainboard of an ender 3 (ender 3/pro/v2). It was created with an SKR e3 v3 in mind, but should work easily with a stock board.</p><p>Needed:</p><p>6 x 4mm threaded M3 inserts (I used <a...
thingiverse
A set of brackets to move PSU from the side to the rear of Ender 3. **Does not fit Pro or V2**. UPDATES: 1. Alternative version **2.0** to be mounted with M5 bolts screwed into tapped holes in openings of profiles. Check if you have those holes...
thingiverse
3. I used nylon standoff screws/nuts from a random amazon kit I had laying around. - There isn't a lot of space between the PSU and the pi 4 but there is an air gap and air flow seems OK. I left the bottom simple so you just hot glue the...
thingiverse
Thingiverse search found me nothing ready to use with the Ender 3 but I still collected a number of elements. This is a remix of those elements from different sources. FreeCad source files included. Basically it's a printed 20x20 extrusion...
prusaprinters
Because from the back you have the best view at the print nozzle when blTouch, the part cooler, the hot end cover and possibly a short led strip all stand in the way for an unobstructed view from the left, right and front of the printer. Thingiverse...
thingiverse
This is a bracket for mounting the spool at the rear of an Ender 3. I turned the Extruder 90 degrees so the filament goes straight in. Full details are here: https://youtu.be/ttPl8WxwHwE I printed it at 25% infill and 0.28 layer height. ...
thingiverse
Ender 3 Rear Clip, i modded the clip from the original file by johnniewhiskey to hold the build plate cable out of the way of the base section, as i found the cable chain i printed was a bit too stiff and would basically change the level of my build...
thingiverse
... bent the spool holder post, or it's a common thing. Long story short, I fractionally changed the angle on the top and added some extra side bracing. This STL is a tinkercad hack job, but it prints and fit's fine on an original Ender 3. . ...
thingiverse
... clean up the divider corners, also the lit is not 100%/exact fit but it is extremely close. I made the changes to sit at the back right corner of my ender 3, right below the PSU. ...The purpose of the box is to house a mini USB hub and some cables.
thingiverse
I modified the left rear case to house a 50mm fan instead of a raspberry pi. ... I would recommend using support blockers in the tight corner below where the fan mounts, I didn't and they were a pain to remove.
thingiverse
I wanted to move the electronics for my Ender 3 to the rear so the USB cable is not hanging off the front of my printer. I'd seen other complete rear case options, but it felt wrong to just discard a perfectly good metal case. Then I realized...
thingiverse
For the "rear_left" I added some loops inside for zipties and filled 2 holes (since my ender does NOT have the 40x40 holes tapped). On rear_right, I filled the same 2 holes. For the front feet, I just cut off the "tab" he had to screw them into the...
thingiverse
One version has a cutout on the bottom to reduce cost and speed up print time For the Ender 3 Pro, see Techaga's [Ender 3 Pro Rear Drawer](https://www.thingiverse.com/thing:3771204). ... Check out my other Ender 3 & 3 Pro Upgrades: Ender 3 & 3 Pro -...
thingiverse
I am uploading the riser feet and rear original Ender 3 PSU mount so you can do the same or similar. Remixes are welcome. I would like to thank Teaching Tech for the original design, starting with that saved me a lot of time and was almost...
thingiverse
I wanted a custom case with adequate airflow for my SKR1.3 board on my ender 3. I loosely based some ideas off of other people's design, but I wanted my own setup for my own needs, primarily having the inlet fan have 5 channels to put air past all...
thingiverse
I've decided to make my own rear box for Ender3 to house SKR 1.3 because the stock box with improvised fan ( mounted externally ) wasn't efficient enough and was too loud. I've also wanted to add in Octoprint and tidy things up a bit when it comes to...
thingiverse
Remix of Teaching Tech's Ender 3 Rear Case. The original was slightly too large for my printer (Ender 3 Pro), so adjusted width by 2mm (now 133mm wide). ...Added 2 extra screw supports for lid.
thingiverse
Trying a Octopus pro just for fun on the Ender 3 and make a remix of Teaching Tech's rear case put for mounts for the Octopus pro. I have not printed this out yet. ... Things still left to do on it are: -add mounts for raspberry pi -add SSR mounts
thingiverse
Original summary: This is a bracket for mounting the spool at the rear of an Ender 3. I turned the Extruder 90 degrees so the filament goes straight in. Full details are here: https://youtu.be/ttPl8WxwHwE I printed it at 25% infill and 0.28...
thingiverse
This is rear drag chain mount is design to be mounted on the extruder bracket for upgraded direct drive ender 3s
thingiverse
I just extended this so it will work on the shorter rails of the Ender 3
thingiverse
This is a bracket for mounting the spool at the rear of an Ender 3. I really liked Chuck's design, which this is a remix of, but I just wanted to change a few things. Here's what I changed: The bracket sits about further out. That, along with...
thingiverse
Both the Y and Z motors should be rotated in the case of Ender 3 Standard (please refer to the position of the motors connectors, as indicated in the attached pictures) - - - - This is the new (improved) version of the motherboard rear case...