mini itx case with atx power supply 3d models

I needed a straightforward solution to attach my power supply to a pipe. No screws were required, and I aimed for a hassle-free installation and disassembly process. ...This project marked my first foray into 3D design.

both 50/105/190mm, one side open One (with round hole) is for electronics with round movement sensor One is for power supply. Edges / corners are specially rounded a bit. Both are printed about 12h and use about 90g of PLA + raft each If willing...

I have used these power supply covers with all my 3D printers and laser engravers in the past years without seeing any need for improvements until one day when I created a short in one of the attached power cables. As these cables were only used on...

This part is not absolutely necessary, but I think it makes a lot of sense.For your power supply, pay attention to the voltage and amperes, use one with at least 12V and preferably 5A. Print:I used the Ender 3 V3 KE, for me it took about 2h and...

I modified the existing shelf bracket to add a spacer so the supply can be mounted with 1 strap and a bracket. ...

An open 3d printed frame for Mini ATX (and a bit larger) motherboards. It is sitting on top of the PSU and has 30mm standoff brass spacers to allow for ventilation of the PSU as well as space to hide the cables. It features support for up to 2x SSD...

Main Features: Customizable modular design Designed to be cut from any flat 8mm thick material (Now available for 6mm material too) Supports 2 slot graphics card up to 10" long (254mm) Supports full size ATX power supply up to 180mm long (160mm max...

His one half covered the new power supply's integrated fan so decided to make this one with a nice tarantula on it. The tarantula was shamelessly taken from this: http://www.thingiverse.com/thing:1668183 I printed at 0.3 and it still took 6 hours,...

His one half covered the new power supply's integrated fan so decided to make this one with a nice tarantula on it. The tarantula was shamelessly taken from http://www.thingiverse.com/thing:1668183. I printed at 0.3 and it still took 6 hours,...

Additions: Larger holes connect directly to the power supply unit (PSU). A better fit for the switch is now available. The XT60 connector provides a secure connection. ...Refer to wiring instructions on Amazon or the original thing:...

I designed this enclosure to accommodate my MKS Gen L board, ATX power supply, ATX breakout, and Raspberry Pi for my 3D printer. I am using it with the Tevo Tarantula components but I'm sure it would work equally well with the same setup. The display...

If you want to build you own PC case, getting the measurements right can be difficult due to the tight tolerances. This template should help you to position the holes for the mainboard standoffs correctly. Update: I added a second version with I/O...

Openbuilds PowerCase with Meanwell LRS-350 Power Supplyhttps://openbuildspartstore.com/powercase-kit/Rough Model,

I upgraded the power supply to USB micro, making it easier to give this mushroom lamp away. Almost everyone has a micro USB cable and a USB charger on hand. To assemble this project, you'll need a 68 Ohm resistor, a Micro USB socket, and a 5mm RGB...

A basic enclosure for a switched power supply is created to fit a 24v 15A unit. Yours may have different dimensions, so measure and modify as needed. I searched for an existing cover design but couldn't find one that met my requirements, so I...

Ideal for ESPresense or any ESP32 application that doesn't require additional connected sensors.Designed around the following parts:FONKEN Power Adapter (https://www.amazon.com/gp/product/B07DCR29GN)D1 Mini ESP32...

Power supply 24V 15A...

40 grams Material pla generic voltmeter and buck converter

5V | 6V | 9V | 12V

I remixed the box to fit usb fast charge ports and quick connect on the side, removed fan grill and added holes in the lid instead as the voltage regulator already got one on his back

5V | 6V | 9V | 12V

Prototype of small ITX computer case

First Finished Rendition of ITX Case

Prototype of small ITX computer case

A compact 24-pin ATX power adapter box, designed specifically for computer systems and ideal for bench-top work or general use. ...This versatile module offers a convenient solution for connecting your PC to a power source.

I added a stop button and an oversized Australian outlet/socket, allowing me to power down the CNC controller with one press, along with any other device plugged into the router. ...As a result, this custom creation looks slightly bulkier due to its...

A simple case for electronics projects, two designs one with mounting ears and one without. Included are the FreeCAD design files. ... The PCB used is https://www.ebay.co.uk/itm/133530666074 Breadboard PSU https://www.ebay.co.uk/itm/133124571919

A compact ITX board, featuring an Intel CPU socket, is inspired by the Asus M2n-e Motherboard (credits to Darren Van Coller). Measuring at 170mm x 170mm, this miniature motherboard delivers big performance. ...Kudos to Darren for his excellent work!

it was inspired by raily74's combined version of the lift with a battery case: https://www.thingiverse.com/thing:5332796, but I wanted something more loosely coupled which fitted in with other Gravitrax objects, disguised as a spacer. I also decided...

The two pieces has two tabs with holes for inserting M3 bolts with nut, which not interferes with the internal psu parts. This is to join the two pieces together. The fan cover needs 4 small screws to screw into the two cover pieces, and 4...